{"id":2701,"date":"2026-09-15T14:55:28","date_gmt":"2026-09-15T06:55:28","guid":{"rendered":"http:\/\/120.77.152.10\/?p=2701"},"modified":"2026-11-09T15:20:57","modified_gmt":"2026-11-09T07:20:57","slug":"%e4%b8%ba%e4%bb%80%e4%b9%88-pp-%e4%bb%a5%e5%89%8d%e8%bf%99%e4%b9%88%e9%9a%be%e6%89%93%ef%bc%9f%e6%94%b6%e7%bc%a9%e3%80%81%e7%bf%98%e8%be%b9%e3%80%81%e7%b2%98%e4%b8%8d%e4%bd%8f%e7%9a%84%e4%b8%89","status":"publish","type":"post","link":"https:\/\/www.polive3d.com\/en\/%e4%b8%ba%e4%bb%80%e4%b9%88-pp-%e4%bb%a5%e5%89%8d%e8%bf%99%e4%b9%88%e9%9a%be%e6%89%93%ef%bc%9f%e6%94%b6%e7%bc%a9%e3%80%81%e7%bf%98%e8%be%b9%e3%80%81%e7%b2%98%e4%b8%8d%e4%bd%8f%e7%9a%84%e4%b8%89\/","title":{"rendered":"Why was PP so difficult to handle in the past? The three main problems are shrinking, curling edges, and not sticking."},"content":{"rendered":"<p class=\"wp-block-paragraph\">Searching in 3D printing communities <strong>\u201cPP filament\u201d<\/strong>, you will often see users discussing several similar questions:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The first layer is hard to stick to the print bed<\/li>\n\n\n\n<li>Edges gradually lift during printing<\/li>\n\n\n\n<li>Large parts are prone to warping<\/li>\n\n\n\n<li>Interlayer bonding is not ideal after printing<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">This does not necessarily mean the print parameters are set incorrectly.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>PP&#8217;s inherent material properties are an important reason why it is difficult to handle in FDM 3D printing.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">PP is an engineering plastic with good lightweight, chemical resistance, moisture resistance, and flexibility, but these material advantages do not mean it is naturally suited for FDM printing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Among them, the three most common challenges are:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>shrinkage and warping, first-layer adhesion, and interlayer bonding.<\/strong><\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Challenge 1: Shrinkage and warping caused by the semi-crystalline structure<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">PP is a<strong>semi-crystalline polymer<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">During cooling, PP undergoes crystallization and volume changes, so the printed part may experience varying degrees of shrinkage in different regions.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For large-size, thin-walled, or structurally complex parts, this shrinkage may further lead to:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>edge lifting \/ warping at the edges<\/li>\n\n\n\n<li>bottom deformation<\/li>\n\n\n\n<li>dimensional deviation<\/li>\n\n\n\n<li>interlayer stress accumulation<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">This is also one of the reasons why PP is harder to print than some common FDM materials such as PLA.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">It should be noted that<strong>PP&#8217;s actual shrinkage rate is not a fixed value that applies to all grades<\/strong>. Material formulation, printing temperature, cooling conditions, part size, and print structure all affect the final result.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, rather than simply attributing PP&#8217;s shrinkage to a certain percentage, it is more important to understand:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>PP&#8217;s semi-crystalline nature makes it more prone to dimensional changes and internal stress during cooling.<\/strong><\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Challenge 2: Low surface energy makes PP hard to adhere to the print bed<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Another typical characteristic of PP is<strong>low surface energy<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This means the surface adhesion between PP and many common materials is weak.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In FDM printing, this directly affects the first layer:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>the first layer is prone to insufficient adhesion<\/li>\n\n\n\n<li>edges are prone to lifting during printing<\/li>\n\n\n\n<li>more noticeable for large parts<\/li>\n\n\n\n<li>different print beds show large differences in performance with PP<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">This is also why, when printing PP,<strong>the choice of print bed and first-layer parameters are very important.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the material lacks sufficient first-layer adhesion, the part may gradually detach from the bed during printing even if the subsequent print parameters are set correctly.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Challenge 3: Interlayer bonding requires better material control<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">FDM 3D printing is not formed in a single step.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The printer forms the final part by depositing molten material layer by layer, so whether the material can form a stable bond between different print layers is very important to the final part&#8217;s mechanical properties.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">PP&#8217;s crystallization behavior, melt flow, and cooling process all affect interlayer bonding.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If interlayer bonding is insufficient, the following may occur:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>insufficient Z-direction strength<\/li>\n\n\n\n<li>interlayer cracking<\/li>\n\n\n\n<li>reduced mechanical performance<\/li>\n\n\n\n<li>the part delaminates after bending or impact<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, PP&#8217;s problem is not just about &#8220;whether it can be extruded from the nozzle.&#8221;<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The real challenge is:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>how to keep the material stable throughout the entire process of printing, cooling, and interlayer fusion.<\/strong><\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>How does POLIVE PPPro\u2122 improve these issues?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">This is also <strong>POLIVE PPPro\u2122 modified PP 3D printing filament<\/strong>&#8216;s core R&amp;D direction.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Compared with ordinary PP, PPPro\u2122 is formulated and performance-tuned to address common material issues in FDM printing, with a focus on:<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>1. Shrinkage and warping control<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">By adjusting the material&#8217;s crystallization behavior and processing characteristics, the risk of deformation caused by cooling and shrinkage during printing is reduced.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>2. Improving first-layer adhesion<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Through material design that addresses the adhesion problem caused by PP&#8217;s low surface energy, PP achieves more stable first-layer performance under suitable print bed and parameter conditions.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>3. Improving interlayer bonding<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">By optimizing the material&#8217;s melting and interlayer fusion performance, a more stable bond is formed between printed layers.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The ultimate goal is not to turn PP into PLA.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Instead, it is:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>to make PP more suitable for FDM 3D printing.<\/strong><\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>No need to change the printer \u2014 solve the problem from the material first<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The difficulties of traditional PP in FDM printing often mean users need to adjust all of the following at once:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Printing temperature<\/li>\n\n\n\n<li>Hotbed temperature<\/li>\n\n\n\n<li>Print speed<\/li>\n\n\n\n<li>Cooling<\/li>\n\n\n\n<li>first-layer parameters<\/li>\n\n\n\n<li>Build platform<\/li>\n\n\n\n<li>Printing environment<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">The significance of modified PP is to start from<strong>the material itself<\/strong>to reduce these difficulties.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">POLIVE PPPro\u2122&#8217;s R&amp;D approach can be summarized as:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>not just enabling PP to be printed, but making PP easier to fit into the actual FDM printing workflow.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Of course, the specific print result still depends on the printer, bed, part size, model structure, and print parameters.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, we recommend performing parameter tests based on the specific equipment, rather than simply copying settings from other materials.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Why choose modified PP?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">PP itself has many properties worth using in 3D printing:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>low density \u2192 lighter<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>chemical resistance \u2192 suitable for more functional environments<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>moisture resistance \u2192 suitable for some outdoor and humid environments<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>flexibility \u2192 suitable for parts that require some elasticity<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>fatigue resistance \u2192 suitable for structures under repeated loads<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The real question is:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Ordinary PP is not easy to print stably.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This is also the value of modified PP 3D printing filament.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>POLIVE PPPro\u2122: Making PP More Suitable for FDM<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">POLIVE specializes in PP-modified 3D printing materials.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>POLIVE PPPro\u2122<\/strong>&nbsp;Its goal is to preserve PP&#8217;s important material properties while improving the typical problems traditional PP encounters during FDM printing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">From material to printing, what we care about is not just one parameter, but the entire printing process:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>material \u2192 melting \u2192 extrusion \u2192 first layer \u2192 interlayer fusion \u2192 cooling \u2192 final part<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Only when the entire process is more stable can PP&#8217;s material advantages truly translate into the actual performance of 3D-printed parts.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>PP being hard to print does not mean it is not worth printing<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">PP was once considered a relatively difficult material to handle in FDM 3D printing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Its problems are not mysterious:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>semi-crystalline \u2192 shrinkage and warping<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>low surface energy \u2192 first-layer adhesion difficulty<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>crystallization and cooling behavior \u2192 interlayer bonding control difficulty<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">But these are precisely the areas where material modification can play a role.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>POLIVE PPPro\u2122&#8217;s core goal is to turn PP from a &#8220;hard-to-print engineering plastic&#8221; into a 3D printing material that is far more suitable for real-world FDM use.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If you are looking for a PP filament more suitable for FDM printing, you can learn more about POLIVE PPPro\u2122.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n<div id=\"rank-math-faq\" class=\"rank-math-block\">\n<div class=\"rank-math-list\">\n<div id=\"faq-question-polive-2701-1\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">Why Was PP So Difficult to Print in the Past?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>It comes down to three things: shrinkage and warping caused by semi-crystallinity, poor first-layer adhesion due to low surface energy, and weak layer bonding. These issues compound one another, which is why a heated bed and an enclosure were often used to force the material into line.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-2701-2\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">With No Heat and No Enclosure, What Keeps Warping in Check?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>Work from both the part and the build plate: replace right-angle corners with rounded fillets, add thickened mouse ears at the base, enlarge the bottom contact area and keep wall thickness uniform; on the plate, add a brim and use PPLOCK26811 adhesive. PP has to shed a great deal of heat as it cools, so in an air-conditioned room, printing with the door and lid open on an open-frame machine actually helps heat dissipate and the part set.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-2701-3\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">If the First Layer Will Not Stick, Is a Heated Bed Essential?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>No. Coat the build plate with a thin layer of PPLOCK26811, let it dry for a few minutes and print directly on it; one application supports several consecutive prints, and cleaning is just a wipe with alcohol. This is more reliable than using heat to make the first layer stick, and it does not depend on the machine.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-2701-4\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">For Poor Layer Bonding, Is an Enclosure the Only Answer?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>An enclosure slows the heat dissipation PP needs, working against the cooling cycle we want. Toolpath and part design are more effective: uniform wall thickness, no abrupt changes in cross-section, and smooth corner transitions. Reduce the shrinkage stress and the layers hold together more reliably on their own.<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n<h2 class=\"wp-block-heading\"><strong>Related Reading<\/strong><strong><\/strong><\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li><a href=\"\/en\/article\/what-is-modified-pp\/\"><u>\u4ec0\u4e48\u662f\u6539\u6027 PP\uff1fPOLIVE PPPro\u2122 \u5230\u5e95\u6539\u4e86\u4ec0\u4e48\uff1f<\/u><\/a>\u00a0<\/li>\n\n\n\n<li><a href=\"\/en\/article\/pp-print-settings\/\"><u>PP 3D \u6253\u5370\u53c2\u6570\u600e\u4e48\u8bbe\u7f6e\uff1fPPPro\u2122 \u53c2\u6570\u6307\u5357<\/u><\/a>\u00a0<\/li>\n\n\n\n<li><a href=\"\/en\/article\/pp-vs-pla\/\"><u>PP or PLA: Which Should You Actually Choose?<\/u><\/a>\u00a0<\/li>\n\n\n\n<li>PP \u5bc6\u5ea6\u4e3a\u4ec0\u4e48\u53ea\u6709\u7ea6 0.90 g\/cm\u00b3\uff1f<\/li>\n<\/ul>","protected":false},"excerpt":{"rendered":"<p>Searching in 3D printing communities \u201cPP filament\u201d, you will often see users discussing several similar questions: This does not necessarily mean the print parameters are set incorrectly. PP&#8217;s i &#8230; <a title=\"Why was PP so difficult to handle in the past? The three main problems are shrinking, curling edges, and not sticking.\" class=\"read-more\" href=\"https:\/\/www.polive3d.com\/en\/%e4%b8%ba%e4%bb%80%e4%b9%88-pp-%e4%bb%a5%e5%89%8d%e8%bf%99%e4%b9%88%e9%9a%be%e6%89%93%ef%bc%9f%e6%94%b6%e7%bc%a9%e3%80%81%e7%bf%98%e8%be%b9%e3%80%81%e7%b2%98%e4%b8%8d%e4%bd%8f%e7%9a%84%e4%b8%89\/\" aria-label=\"Read more about \u4e3a\u4ec0\u4e48 PP \u4ee5\u524d\u8fd9\u4e48\u96be\u6253\uff1f\u6536\u7f29\u3001\u7fd8\u8fb9\u3001\u7c98\u4e0d\u4f4f\u7684\u4e09\u5927\u96be\u9898\u3002\">Read more<\/a><\/p>","protected":false},"author":1,"featured_media":2704,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[35],"tags":[],"class_list":["post-2701","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-35","infinite-scroll-item","generate-columns","tablet-grid-50","mobile-grid-100","grid-parent","grid-33"],"_links":{"self":[{"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/posts\/2701","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/comments?post=2701"}],"version-history":[{"count":3,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/posts\/2701\/revisions"}],"predecessor-version":[{"id":4039,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/posts\/2701\/revisions\/4039"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/media\/2704"}],"wp:attachment":[{"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/media?parent=2701"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/categories?post=2701"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/tags?post=2701"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}