{"id":3416,"date":"2026-10-09T15:15:00","date_gmt":"2026-10-09T07:15:00","guid":{"rendered":"https:\/\/www.polive3d.com\/?p=3416"},"modified":"2026-11-09T15:20:29","modified_gmt":"2026-11-09T07:20:29","slug":"pp-%e6%89%93%e5%8d%b0%e6%80%8e%e4%b9%88%e9%98%b2%e7%bf%98%e8%be%b9%ef%bc%9fbrim%e3%80%81raft-%e4%b8%8e%e8%a3%99%e8%be%b9%e6%80%8e%e4%b9%88%e9%80%89-url-slug","status":"publish","type":"post","link":"https:\/\/www.polive3d.com\/en\/pp-%e6%89%93%e5%8d%b0%e6%80%8e%e4%b9%88%e9%98%b2%e7%bf%98%e8%be%b9%ef%bc%9fbrim%e3%80%81raft-%e4%b8%8e%e8%a3%99%e8%be%b9%e6%80%8e%e4%b9%88%e9%80%89-url-slug\/","title":{"rendered":"How to Prevent PP Warping? How to Choose Between Brim, Raft, and Skirt"},"content":{"rendered":"<h2 class=\"wp-block-heading\">How to Prevent PP Warping? How to Choose Between Brim, Raft, and Skirt<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Use a brim and PPLOCK26811, plus geometry: fillet sharp corners, add mouse ears, widen the bottom contact area and keep wall thickness even.<\/p>\n\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<p class=\"wp-block-paragraph\">PP print warping usually relates to the balance between the stress caused by material cooling shrinkage and plate adhesion.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When choosing auxiliary structures, PP printing can usually prioritize <strong>Brim<\/strong>: it can expand the effective adhesion area between the part and the plate, while distributing some of the shrinkage stress, and it is relatively easy to remove after printing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">**Skirt** is mainly used to check the first layer and stabilize extrusion; it basically provides no warping prevention.<strong>Raft<\/strong> It can provide a larger adhesion base, but it increases material consumption and print time.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">However, Brim is not the only way to solve all warping problems. Plate condition, first-layer settings, environmental conditions, the cooling fan, and model structure all need to be considered together.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For POLIVE PPpro\u00e2\u0084\u00a2, you also need to combine the product&#8217;s actual printing positioning, focusing on plate adhesion, environmental stability, and cooling uniformity\u00e2\u0080\u0094rather than simply relying on raising the heated-bed temperature to solve warping.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How Does Warping Happen?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">PP shrinks as it cools after being melted and extruded.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the cooling rates of different regions differ significantly, shrinkage stress can build up. When the shrinkage acting on the part&#8217;s edges exceeds its adhesion to the build plate, the corners may gradually lift away from the plate and warp upward.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, PP warping can usually be improved from two directions:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Reduce the shrinkage stress caused by uneven cooling + increase plate adhesion.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Reducing shrinkage stress can start from material properties, print speed, environmental conditions, and cooling uniformity; increasing adhesion can be achieved through plate material, first-layer settings, and auxiliary structures such as Brim and Raft.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Brim and Raft are essentially methods that increase the effective adhesion area and improve adhesion conditions.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How to Choose Between Skirt, Brim, and Raft?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The three structures look similar, but their actual functions differ.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Skirt<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A skirt is one or more loops of lines printed around the part&#8217;s perimeter, but it is not connected to the part itself.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Its main role is not to increase the part&#8217;s adhesion area, but to help the printer before formally printing the part:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Stabilize extrusion<\/li>\n\n\n\n<li>Check whether the nozzle is extruding normally<\/li>\n\n\n\n<li>Observe the first-layer height and flow<\/li>\n\n\n\n<li>Detect bed-leveling issues early<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, a skirt provides very limited direct help in preventing PP warping.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If your goal is to prevent warping rather than to check the first layer, then you should prioritize Brim.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Brim<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A brim is a thin edge extending outward around the bottom perimeter of the part, and it is connected to the part.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">It can expand the effective contact area between the part and the plate, distributing the shrinkage effect over a larger area, thereby reducing the likelihood of edges lifting off the plate.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For PP printing, Brim is usually the most practical first choice.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Its advantages include:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Increased adhesion area<\/li>\n\n\n\n<li>Targeted at corner lifting<\/li>\n\n\n\n<li>Less material increase compared to Raft<\/li>\n\n\n\n<li>Relatively limited increase in print time<\/li>\n\n\n\n<li>Relatively easy to remove after printing<\/li>\n<\/ul>\n\n\n\n<h4 class=\"wp-block-heading\">How to Set the Brim Width?<\/h4>\n\n\n\n<p class=\"wp-block-paragraph\">You can start testing with a smaller width, then adjust based on the model size and the degree of warping.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example, you can use the following values as a starting point for testing:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Small parts: 3\u00e2\u0080\u00935 mm<\/li>\n\n\n\n<li>Medium parts: 5\u00e2\u0080\u00938 mm<\/li>\n\n\n\n<li>Large-area parts: increase further based on the actual warping situation<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">These values are more suitable as a starting point for parameter testing, rather than fixed standards that apply to all models.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For large parts, if simply increasing the Brim width still cannot solve warping, you should go back and check plate adhesion, environmental conditions, cooling uniformity, and model structure, rather than increasing the Brim indefinitely.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Raft<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A raft is an independent base layer printed first beneath the part, on which the part is then built.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Compared with Brim, a raft can provide a more complete bottom base, so it may be more helpful when the plate condition is poor or the model is particularly difficult to print.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Its advantages include:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Provides a larger bottom adhesion base<\/li>\n\n\n\n<li>Can somewhat reduce the direct impact of plate surface condition on the model&#8217;s bottom<\/li>\n\n\n\n<li>More useful for models with complex bottom shapes or poor plate conditions<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">But it also has obvious costs:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Increased material consumption<\/li>\n\n\n\n<li>Increased print time<\/li>\n\n\n\n<li>More complex post-processing<\/li>\n\n\n\n<li>The bottom of the part may be less flat than printing directly on the plate<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, Raft is more suitable for difficult printing scenarios where Brim still cannot solve the problem, rather than as the default setting for all PP printing.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">What Are the Differences Between Brim, Raft, and Skirt?<\/h2>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><tbody><tr><th>Auxiliary structure<\/th><th>Increases adhesion area?<\/th><th>Main function<\/th><th>PP warping prevention effect<\/th><th>Material and time<\/th><\/tr><tr><td>Skirt<\/td><td>No<\/td><td>Check extrusion, first layer<\/td><td>Very limited<\/td><td>Less increase<\/td><\/tr><tr><td>Brim<\/td><td>Yes<\/td><td>Increases edge adhesion<\/td><td>Usually practical<\/td><td>Less increase<\/td><\/tr><tr><td>Raft<\/td><td>Yes<\/td><td>Provides bottom base<\/td><td>May help more in some difficult scenarios<\/td><td>More increase<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Simply put:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Skirt is for checking, Brim is for strengthening adhesion, and Raft is for handling more difficult situations.<\/strong><\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Not Enough with Brim Alone? Check These Factors<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">If you have already increased the Brim but PP still warps noticeably, do not keep simply increasing the Brim width.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">You can troubleshoot in the following order.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">1. Check the build plate<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">First, confirm that the plate is clean and that the plate material used is suitable for PP.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">You can consider options such as PP film or PP board, and check whether the first layer forms a stable, continuous contact.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A relatively intuitive way to judge is to observe the first layer:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The first-layer lines should have a certain degree of compaction, while remaining clear and continuous\u00e2\u0080\u0094not obviously floating or over-extruded.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If there is oil, dust, or residue on the plate surface, it may also affect adhesion performance.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">2. Check the environment and cooling<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">During PP printing, both environmental conditions and whether cooling is uniform affect the part&#8217;s shrinkage and warping.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For POLIVE PPpro\u00e2\u0084\u00a2, it is recommended to<strong>print in a relatively stable indoor environment such as an air-conditioned room, and focus on whether the cooling of each region of the print is uniform<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">You can check:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Whether the printing environment has obvious temperature fluctuations<\/li>\n\n\n\n<li>Whether the cooling rates of different regions of the print differ significantly<\/li>\n\n\n\n<li>Whether the edges of large parts are more prone to lifting<\/li>\n\n\n\n<li>Whether local deformation occurs at thin walls, sharp corners, or long edges<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">If the cooling differences between regions are obvious, adjustments can be made in combination with the model structure and print settings.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The key is not to blindly raise the surrounding temperature, but to minimize the shrinkage stress caused by uneven cooling.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">3. Check the cooling fan settings<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The cooling fan affects the material&#8217;s heat dissipation rate.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If cooling is too fast at the beginning of printing, it may affect first-layer stability and subsequent interlayer bonding. Therefore, based on actual print performance, you can appropriately adjust the fan-on time or fan speed for the first few layers, then observe the first layer and corner conditions.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">However, fan settings should not be judged in isolation from the specific material and print parameters. When adjusting, change only one major variable at a time to make results easier to compare.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">4. Adjust the first-layer print settings<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The first layer is the foundation for the entire part to establish adhesion with the plate.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">You can conduct small-scale tests on the following parameters based on the actual situation of the equipment and material:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>First-layer speed<\/li>\n\n\n\n<li>First-layer line width<\/li>\n\n\n\n<li>First-layer height<\/li>\n\n\n\n<li>First-layer extrusion amount<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">If the first-layer gap is too large, the filament may not spread sufficiently; if there is too much extrusion, it may also cause an uneven first layer or edge buildup.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">It is recommended to first confirm whether the first layer is uniform and continuous, then decide whether further extrusion adjustments are needed.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Model design also affects warping<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Some warping problems are not entirely caused by print parameters; the model&#8217;s own structure can also amplify shrinkage stress.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Sharp right angles<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Sharp outer corners easily become locations where shrinkage stress concentrates.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the design allows, you can use appropriate fillets instead of very sharp right angles to reduce the deformation risk from local stress concentration.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Large flat bottom<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Large-area parts may accumulate noticeable shrinkage stress during cooling.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, besides using Brim, you also need to pay special attention to plate adhesion, environmental stability, and whether overall cooling is uniform.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Enclosed frame structure<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">For some frame-type parts, shrinkage stress may concentrate in the middle region of longer edges.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For such models, besides adjusting print parameters, you can also start from the model orientation and structural design, and add process connection structures when necessary to reduce the risk of local deformation.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How Should You Combine Warping-Prevention Measures?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">If you are just starting to print PP, you can use a relatively simple troubleshooting sequence.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Step 1: Check the plate<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Clean the plate and confirm that the first layer can adhere stably.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">\u2193<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Step 2: Check the first layer<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Confirm that the first-layer height, line spreading, and extrusion state are reasonable.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">\u2193<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Step 3: Focus on environment and cooling<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Print in a relatively stable air-conditioned room, and focus on whether cooling is uniform.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">\u2193<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Step 4: Use Brim<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If corners still lift, prioritize increasing the Brim rather than using Raft directly.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">\u2193<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Step 5: Adjust cooling and first-layer parameters<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Adjust the fan settings, first-layer speed, and extrusion settings for the first few layers based on actual performance.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">\u2193<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Step 6: Check the model structure<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If it is a large, sharp-cornered, or complex structure, then optimize from the model design and orientation.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This approach makes it easier to find the factors that truly affect warping than changing multiple parameters at once from the start.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Summary<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">PP warping is essentially related to the balance between shrinkage stress and plate adhesion. Preventing warping usually requires troubleshooting from two directions: reducing the shrinkage stress caused by uneven cooling, and increasing plate adhesion.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>**Skirt** is mainly used to check extrusion and first-layer status; it itself adds almost no adhesion.<\/li>\n\n\n\n<li><strong>Brim<\/strong> It can expand the adhesion area and is the most practical preferred auxiliary structure in PP printing.<\/li>\n\n\n\n<li><strong>Raft<\/strong> It provides a more complete bottom base and is more suitable for difficult models with poor plate conditions or where Brim still cannot solve the problem.<\/li>\n\n\n\n<li>Plate cleanliness and first-layer condition are the foundation; Brim can only serve as further assistance.<\/li>\n\n\n\n<li>Large parts should pay special attention to environmental stability, cooling uniformity, and plate adhesion, rather than simply increasing the Brim width.<\/li>\n\n\n\n<li>If warping persists after using Brim, you should continue to check the plate, environment, cooling fan, first-layer parameters, and model structure.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">For POLIVE PPpro\u00e2\u0084\u00a2, it is recommended to print in a relatively stable air-conditioned room and verify with a suitable plate, Brim settings, and uniform cooling\u00e2\u0080\u0094rather than relying on a single warping-prevention measure.<\/p>\n\n\n<div id=\"rank-math-faq\" class=\"rank-math-block\">\n<div class=\"rank-math-list\">\n<div id=\"faq-question-polive-3416-1\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">How Does Warping Actually Happen in PP?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>As the material cools and shrinks it builds up internal stress. When that stress exceeds the first layer's adhesion to the build plate, the corners get pulled up. So you can work from either end: reduce the stress or improve the adhesion.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3416-2\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">How Do You Choose Between Skirt, Brim and Raft?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>A Skirt only primes the nozzle and adds no adhesion, while a Raft wastes material and time and leaves a poor bottom surface. Our standard approach is a Brim combined with a dedicated adhesive: coat the build plate thinly with PPLOCK26811, let it dry, and one application lasts for multiple prints; cleaning is just a wipe with alcohol.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3416-3\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">A Brim Alone Is Not Enough \u2014 What Else Should You Check?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>Check that the plate is clean, the adhesive is fully dry, and first-layer height and extrusion are correct; look for draughts or local heat sources in the room, and whether cooling is even. These do more than repeatedly widening the brim.<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3416-4\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">How Much Warping Can Part Design Solve?<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>A large part of it. Replacing right angles with rounded fillets, adding thickened mouse ears at the base, enlarging the bottom contact area and keeping wall thickness as uniform as possible all reduce shrinkage stress at its source. On the Bambu A1 we rely mainly on these design measures for large flat parts, not on a heated bed or an enclosure.<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n<h2 class=\"wp-block-heading\">Related Reading<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>What Print Bed Should Be Used for PP 3D Printing? A Comparison of Common Bed Materials<\/strong><\/li>\n\n\n\n<li><strong>\u4e3a\u4ec0\u4e48 PP \u4ee5\u524d\u8fd9\u4e48\u96be\u6253\uff1f\u6536\u7f29\u3001\u7fd8\u8fb9\u3001\u7c98\u4e0d\u4f4f\u7684\u4e09\u5927\u96be\u9898<\/strong><\/li>\n\n\n\n<li><strong>How to Configure PP 3D Printing Settings? PPpro\u2122 Parameter Guide<\/strong><\/li>\n\n\n\n<li><strong>What Is PP&#8217;s Melting Point? How Should PP Printing Temperature Be Understood<\/strong><\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>","protected":false},"excerpt":{"rendered":"<p>How to Prevent PP Warping? How to Choose Between Brim, Raft, and Skirt Use a brim and PPLOCK26811, plus geometry: fillet sharp corners, add mouse ears, widen the bottom contact area and keep wall thic &#8230; <a title=\"How to Prevent PP Warping? How to Choose Between Brim, Raft, and Skirt\" class=\"read-more\" href=\"https:\/\/www.polive3d.com\/en\/pp-%e6%89%93%e5%8d%b0%e6%80%8e%e4%b9%88%e9%98%b2%e7%bf%98%e8%be%b9%ef%bc%9fbrim%e3%80%81raft-%e4%b8%8e%e8%a3%99%e8%be%b9%e6%80%8e%e4%b9%88%e9%80%89-url-slug\/\" aria-label=\"Read more about PP \u6253\u5370\u600e\u4e48\u9632\u7fd8\u8fb9\uff1fBrim\u3001Raft \u4e0e\u88d9\u8fb9\u600e\u4e48\u9009  URL Slug\">Read more<\/a><\/p>","protected":false},"author":1,"featured_media":3417,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[35],"tags":[155,154,156,153,152,151],"class_list":["post-3416","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-35","tag-3d","tag-brim-raft-","tag-polypropylene-warping","tag-pp-bed-adhesion","tag-pp-","tag-pp","infinite-scroll-item","generate-columns","tablet-grid-50","mobile-grid-100","grid-parent","grid-33"],"_links":{"self":[{"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/posts\/3416","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/comments?post=3416"}],"version-history":[{"count":6,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/posts\/3416\/revisions"}],"predecessor-version":[{"id":4022,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/posts\/3416\/revisions\/4022"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/media\/3417"}],"wp:attachment":[{"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/media?parent=3416"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/categories?post=3416"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.polive3d.com\/en\/wp-json\/wp\/v2\/tags?post=3416"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}