{
    "id": 3407,
    "date": "2026-10-08T21:00:00",
    "date_gmt": "2026-10-08T13:00:00",
    "guid": {
        "rendered": "https:\/\/www.polive3d.com\/?p=3407"
    },
    "modified": "2026-11-09T15:20:34",
    "modified_gmt": "2026-11-09T07:20:34",
    "slug": "pp-3d-%e6%89%93%e5%8d%b0%e7%94%a8%e4%bb%80%e4%b9%88%e6%89%93%e5%8d%b0%e5%b9%b3%e5%8f%b0%ef%bc%9f%e5%b8%b8%e8%a7%81%e5%b9%b3%e5%8f%b0%e6%9d%90%e6%96%99%e5%af%b9%e6%af%94",
    "status": "publish",
    "type": "post",
    "link": "https:\/\/www.polive3d.com\/zh_cn\/pp-3d-%e6%89%93%e5%8d%b0%e7%94%a8%e4%bb%80%e4%b9%88%e6%89%93%e5%8d%b0%e5%b9%b3%e5%8f%b0%ef%bc%9f%e5%b8%b8%e8%a7%81%e5%b9%b3%e5%8f%b0%e6%9d%90%e6%96%99%e5%af%b9%e6%af%94\/",
    "title": {
        "rendered": "PP 3D \u6253\u5370\u7528\u4ec0\u4e48\u6253\u5370\u5e73\u53f0\uff1f\u5e38\u89c1\u5e73\u53f0\u6750\u6599\u5bf9\u6bd4"
    },
    "content": {
        "rendered": "<h2 class=\"wp-block-heading\">What Print Bed Should Be Used for PP 3D Printing? A Comparison of Common Bed Materials<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">PP bonds poorly to most surfaces, so plate prep matters more than heat. A brim and PPLOCK26811 hold parts; alcohol cleans the plate.<\/p>\n\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\">What print bed should be used for PP 3D printing?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">When choosing a bed for PP 3D printing, the core is not simply pursuing &#8220;the stickier the better,&#8221; but satisfying two conditions at the same time:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>It must adhere during printing and be removable after printing.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">PP is a low-surface-energy material and shrinks during cooling. Therefore, bed selection needs to consider both adhesion and demolding.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Common beds such as ordinary glass and PEI may not directly achieve ideal PP adhesion. In practice, options such as PP sheet, PP printing sticker film, or PP-specific specialized tape can be considered.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For a specific bed, it is best to first verify with small test prints before moving to larger prints.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Why is PP picky about the print bed?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">PP is a polyolefin material with relatively low surface energy.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This leads to a direct problem:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Molten PP does not easily wet certain bed surfaces well.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">At the same time, PP is a semi-crystalline material that shrinks during cooling.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, PP printing actually needs to solve two problems at the same time.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">First: allow the first layer to adhere fully<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">If the wetting and interfacial bonding between the molten material and the bed are insufficient, the first layer may easily detach.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Second: control warping caused by cooling shrinkage<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Even if the first layer has adhered, the shrinkage stress generated during subsequent cooling may lift the edges upward.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>PP bed selection = adhesion + warping resistance + demolding<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">You cannot just look at whether the bed &#8220;sticks.&#8221;<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Comparison of Common PP Print Bed Materials<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The performance of different beds is affected by factors such as PP formulation, bed surface condition, printing parameters, and first-layer conditions. The following can serve as a basic reference when choosing.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">1. Glass<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The biggest advantage of glass is:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Flat surface<\/li>\n\n\n\n<li>Easy to clean<\/li>\n\n\n\n<li>The bottom surface is usually relatively flat<\/li>\n\n\n\n<li>Relatively easy part removal<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">But for PP, direct adhesion on bare glass is usually insufficient.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, if you use a glass bed to print PP, it usually needs to be combined with:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Glue<\/li>\n\n\n\n<li>Tape<\/li>\n\n\n\n<li>Specialized film<\/li>\n\n\n\n<li>Other surface treatments suitable for PP<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Glass is more suitable as a base bed, rather than assuming bare glass alone can stably print PP by default.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">2. PEI (Polyetherimide) Sheet<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">PEI is currently one of the most common general-purpose 3D printing bed materials, and usually provides good adhesion for materials such as PLA and PETG.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">But PP behaves differently on PEI.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Since PP itself is a low-surface-energy material, PP&#8217;s direct adhesion on PEI is affected by the specific material formulation and bed surface condition.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, it is not recommended to simply assume:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">&#8220;PEI is a general-purpose bed, so it must be suitable for PP.&#8221;<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A more reasonable approach is to first verify with small test prints:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Whether the first layer is stable<\/li>\n\n\n\n<li>Whether the edges lift<\/li>\n\n\n\n<li>Whether detachment occurs during printing<\/li>\n\n\n\n<li>Whether the part is easy to remove after printing<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-heading\">3. Masking Tape \/ Specialized Tape<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The main advantages of the tape solution are:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Low cost<\/li>\n\n\n\n<li>Easy to replace<\/li>\n\n\n\n<li>Can quickly adjust the bed surface<\/li>\n\n\n\n<li>Helps with edge adhesion for some PP prints<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">But it also has some disadvantages:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Limited service life<\/li>\n\n\n\n<li>Tape seams may leave marks on the bottom surface<\/li>\n\n\n\n<li>For large prints over long durations, edges may still be lifted by shrinkage stress<\/li>\n\n\n\n<li>After each replacement, the bed condition may change<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, tape is suitable for low-cost testing and some printing scenarios, but for long-term stable production, a more durable bed solution needs to be considered.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">4. PP Sheet \/ PP Printing Sticker Film<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">This is an approach considered from the perspective of material compatibility.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Simply put, it tries to use a surface similar to the printing material as the print bed.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">PP sheet or PP printing sticker film can serve as a testing solution for PP printing. However, the specific adhesion performance still needs to be verified based on the actual material, bed surface, and printing conditions.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Under our test conditions, this type of bed solution is a direction worth prioritizing for testing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>PPpro\u00e2\u0084\u00a2 adhesion comparison tests across beds: data to be added.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">At the same time, it should also be noted that:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Stronger adhesion is not always better.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the bed and the print are bonded too strongly, the following may instead occur after printing:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Difficulty removing the part<\/li>\n\n\n\n<li>Damage to the bottom surface of the print<\/li>\n\n\n\n<li>Wear on the bed surface<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, an ideal PP bed should maintain stable adhesion during printing and allow relatively easy demolding after printing.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">5. Glue-Based Auxiliary Solutions<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">If your existing printer uses a glass or PEI bed, you can also consider using a PP-compatible bed glue or other auxiliary bonding solutions.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">They can serve as a supplement to bed adhesion.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">But you need to pay attention to the amount used.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A glue layer that is too thick may:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Affect the first-layer surface<\/li>\n\n\n\n<li>Change the first-layer height<\/li>\n\n\n\n<li>Affect bottom-surface flatness<\/li>\n\n\n\n<li>Increase cleaning difficulty<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, glue is more suitable as an auxiliary solution, rather than simply solving all adhesion problems by continuously increasing the amount of glue.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How should you choose a PP print bed?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">If you are just starting to try PP 3D printing, you can choose according to the following approach.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><tbody><tr><th>Bed option<\/th><th>PP adhesion approach<\/th><th>Key features<\/th><\/tr><tr><td>Bare glass<\/td><td>Usually requires auxiliary treatment<\/td><td>Flat, easy to clean<\/td><\/tr><tr><td>PEI<\/td><td>Requires actual verification<\/td><td>Strong versatility, but PP performance depends on material and surface<\/td><\/tr><tr><td>Masking tape \/ specialized tape<\/td><td>Can serve as a low-cost solution<\/td><td>Low cost, easy to replace, but limited lifespan<\/td><\/tr><tr><td>PP sheet \/ PP film<\/td><td>Material compatibility approach<\/td><td>Worth prioritizing for testing, suitable for PP scenarios<\/td><\/tr><tr><td>Glue assistance<\/td><td>Improves adhesion on existing beds<\/td><td>Flexible to use, but requires controlling the amount<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">If it is your first time printing PP, it is not recommended to test directly with a large part.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A more reasonable approach is:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Small test prints \u00e2\u0086\u0092 confirm bed adhesion \u00e2\u0086\u0092 adjust first layer \u00e2\u0086\u0092 check environment and cooling \u00e2\u0086\u0092 then print large parts<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This can reduce waste of material and time.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">How should the bed surface be prepared?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Regardless of which bed is used, pre-print preparation directly affects first-layer performance.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">1. Keep the bed clean<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Before printing, try to remove:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Fingerprints<\/li>\n\n\n\n<li>Oil stains<\/li>\n\n\n\n<li>Dust<\/li>\n\n\n\n<li>Glue residue<\/li>\n\n\n\n<li>Other contaminants<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">You can choose an appropriate cleaning method based on the bed material.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">After cleaning, also try to avoid touching the printing area directly with your hands.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">2. Adjust the first-layer height<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The first layer of PP needs to form sufficient actual contact with the bed.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the first-layer gap is too large, it may lead to:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Insufficient melt spreading<\/li>\n\n\n\n<li>Insufficient contact area<\/li>\n\n\n\n<li>Reduced first-layer adhesion<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, even if the bed itself is suitable for PP, improper first-layer height settings may cause the print to detach from the bed.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">3. Pay attention to environment and cooling<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Bed material is only one factor affecting print results. Printing environment and cooling conditions also affect first-layer stability, print shrinkage, and warping.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">It is recommended to focus on:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Whether there is airflow blowing directly onto the print<\/li>\n\n\n\n<li>Whether the printing environment has obvious temperature fluctuations<\/li>\n\n\n\n<li>Whether the cooling of different regions of the print is uniform<\/li>\n\n\n\n<li>Whether large parts or sharp-corner regions are more prone to warping<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">For POLIVE PPpro\u00e2\u0084\u00a2, its product positioning is room-temperature printing, no heat bed required, and open-frame printing. In actual use, you should focus on environmental stability and cooling uniformity, rather than defaulting to solving all adhesion or warping issues by raising the heat-bed temperature.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">4. Check bed wear<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Tape and printing sticker film are themselves consumables.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If you notice:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Edge lifting<\/li>\n\n\n\n<li>Scratches<\/li>\n\n\n\n<li>Obvious indentations<\/li>\n\n\n\n<li>Surface wear<\/li>\n\n\n\n<li>Localized abnormal adhesion<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">you should consider replacing it.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Do not wait until the bed suddenly releases the print during a large job to discover that the bed surface can no longer provide stable adhesion.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Why is &#8220;stickier&#8221; sometimes worse?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">This is a point easily overlooked when choosing a PP bed.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">An ideal bed does not glue the print down firmly, but keeps the print stable during printing and allows controllable demolding after printing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If adhesion is too weak:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Insufficient adhesion \u00e2\u0086\u0092 edge lifting \u00e2\u0086\u0092 print failure<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If adhesion is too strong:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Difficulty removing \u00e2\u0086\u0092 bottom-surface damage \u00e2\u0086\u0092 bed wear<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, when evaluating a PP print bed, you should observe both the adhesion during printing and the demolding performance after printing, rather than only testing whether it &#8220;sticks&#8221; during printing.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">What bed should PPpro\u00e2\u0084\u00a2 be paired with?<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">For POLIVE PPpro\u00e2\u0084\u00a2, bed selection should still be tested in combination with the actual printer and printing conditions.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Since PPpro\u00e2\u0084\u00a2 is a modified PP filament formulated for FDM 3D printing, its material design focuses on:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Platform attachment<\/li>\n\n\n\n<li>Shrinkage behavior<\/li>\n\n\n\n<li>Melt flow<\/li>\n\n\n\n<li>Interlayer bonding<\/li>\n\n\n\n<li>Printing stability<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">In actual use, you can prioritize testing bed solutions suitable for PP, then adjust based on first-layer performance.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Ultimately, the actual test results of the following combination should be the standard:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>PPpro\u00e2\u0084\u00a2 + current printer + bed + printing parameters + environment and cooling conditions<\/strong><\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Summary<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The core of a PP print bed is not simply pursuing the strongest adhesion, but achieving stable adhesion and easy demolding.<\/li>\n\n\n\n<li>PP&#8217;s low surface energy makes its direct adhesion on some general-purpose beds relatively difficult.<\/li>\n\n\n\n<li>PP shrinks during cooling, so bed adhesion and warping resistance need to be considered together.<\/li>\n\n\n\n<li>Bare glass usually needs to be combined with glue, tape, or other surface treatments.<\/li>\n\n\n\n<li>PEI is a common general-purpose bed, but PP&#8217;s performance on PEI should be confirmed through actual testing.<\/li>\n\n\n\n<li>Masking tape or specialized tape is low cost, but its lifespan and stability for large prints are limited.<\/li>\n\n\n\n<li>PP sheet or PP printing sticker film is a PP bed solution worth testing.<\/li>\n\n\n\n<li>Bed cleanliness, first-layer height, environmental stability, and cooling uniformity also affect the final result.<\/li>\n\n\n\n<li>When testing a new bed for the first time, it is recommended to first print small test pieces, then proceed to larger prints.<\/li>\n\n\n\n<li>For POLIVE PPpro\u00e2\u0084\u00a2, you should verify the optimal printing conditions based on the specific printer and bed combination, and follow the product&#8217;s corresponding printing guide.<\/li>\n<\/ul>\n\n\n<div id=\"rank-math-faq\" class=\"rank-math-block\">\n<div class=\"rank-math-list\">\n<div id=\"faq-question-polive-3407-1\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">PP \u6253\u5370\u8be5\u7528\u4ec0\u4e48\u5e73\u53f0\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u6838\u5fc3\u4e0d\u662f\u8d8a\u7c98\u8d8a\u597d\uff0c\u800c\u662f\u540c\u65f6\u6ee1\u8db3\u9996\u5c42\u8d34\u5f97\u4f4f\u548c\u80fd\u63a7\u5236\u51b7\u5374\u6536\u7f29\u3002\u73bb\u7483\u3001PEI\u3001\u7f8e\u7eb9\u7eb8\u3001\u4e13\u7528\u80f6\u5e26\u3001PP \u677f\u5404\u6709\u53d6\u820d\uff0c\u9009\u62e9\u8981\u770b\u4f60\u914d\u7684\u7c98\u9644\u65b9\u6848\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3407-2\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">PPpro\u2122 \u7684\u5e73\u53f0\u600e\u4e48\u914d\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u4e0d\u7528\u53cd\u590d\u8d34 PP \u80f6\u5e26\u3002\u5e73\u53f0\u8584\u6d82 PPLOCK26811 \u4e13\u7528\u80f6\u6c34\uff0c\u7b49\u51e0\u5206\u949f\u5e72\u900f\u540e\u76f4\u63a5\u6253\u5370\uff0c\u52a0\u88d9\u8fb9\u5373\u53ef\uff1b\u4e00\u6b21\u6d82\u62b9\u53ef\u4ee5\u591a\u6b21\u6253\u5370\uff0c\u9700\u8981\u6e05\u6d01\u7528\u9152\u7cbe\u64e6\u6389\u91cd\u6d82\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3407-3\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">\u4e3a\u4ec0\u4e48\u6709\u65f6\u5019\u592a\u7c98\u53cd\u800c\u4e0d\u597d\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u7c98\u5f97\u8fc7\u6b7b\u4f1a\u8ba9\u8131\u6a21\u65f6\u4f24\u5230\u5e73\u53f0\u6d82\u5c42\u6216\u96f6\u4ef6\uff0c\u5c24\u5176 PP \u97e7\u6027\u597d\u3001\u786c\u64ac\u5bb9\u6613\u628a\u5e95\u5c42\u6495\u574f\u3002\u66f4\u7a33\u7684\u662f\u8ba9\u6d82\u5c42\u63d0\u4f9b\u5747\u5300\u9002\u4e2d\u7684\u9644\u7740\uff0c\u7b49\u5e73\u53f0\u81ea\u7136\u51b7\u5374\u540e\u518d\u53d6\u4ef6\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3407-4\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">\u4e0d\u52a0\u70ed\u5e8a\uff0c\u5e73\u53f0\u8fd8\u8981\u505a\u4ec0\u4e48\u51c6\u5907\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u628a\u8868\u9762\u6cb9\u6c61\u7528\u9152\u7cbe\u64e6\u51c0\u3001\u786e\u8ba4\u80f6\u6c34\u5e72\u900f\u3001\u68c0\u67e5\u9996\u5c42\u9ad8\u5ea6\uff1b\u73af\u5883\u4e0a\u653e\u5728\u7a7a\u8c03\u623f\u3001\u907f\u5f00\u7a7f\u5802\u98ce\uff0c\u8ba9 PP \u5f00\u653e\u6563\u70ed\u5747\u5300\u5b9a\u578b\u3002<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n<h2 class=\"wp-block-heading\">Related Reading<\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>How to Prevent PP Warping? How to Choose Between Brim, Raft, and Skirt<\/strong><\/li>\n\n\n\n<li><strong>\u4e3a\u4ec0\u4e48 PP \u4ee5\u524d\u8fd9\u4e48\u96be\u6253\uff1f\u6536\u7f29\u3001\u7fd8\u8fb9\u3001\u7c98\u4e0d\u4f4f\u7684\u4e09\u5927\u96be\u9898<\/strong><\/li>\n\n\n\n<li><strong>How to Configure PP 3D Printing Settings? PPpro\u2122 Parameter Guide<\/strong><\/li>\n\n\n\n<li><strong>What Is PP&#8217;s Melting Point? How Should PP Printing Temperature Be Understood<\/strong><\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>",
        "protected": false
    },
    "excerpt": {
        "rendered": "<p>What Print Bed Should Be Used for PP 3D Printing? A Comparison of Common Bed Materials PP bonds poorly to most surfaces, so plate prep matters more than heat. A brim and PPLOCK26811 hold parts; alcoho &#8230; <a title=\"PP 3D \u6253\u5370\u7528\u4ec0\u4e48\u6253\u5370\u5e73\u53f0\uff1f\u5e38\u89c1\u5e73\u53f0\u6750\u6599\u5bf9\u6bd4\" class=\"read-more\" href=\"https:\/\/www.polive3d.com\/zh_cn\/pp-3d-%e6%89%93%e5%8d%b0%e7%94%a8%e4%bb%80%e4%b9%88%e6%89%93%e5%8d%b0%e5%b9%b3%e5%8f%b0%ef%bc%9f%e5%b8%b8%e8%a7%81%e5%b9%b3%e5%8f%b0%e6%9d%90%e6%96%99%e5%af%b9%e6%af%94\/\" aria-label=\"\u9605\u8bfb PP 3D \u6253\u5370\u7528\u4ec0\u4e48\u6253\u5370\u5e73\u53f0\uff1f\u5e38\u89c1\u5e73\u53f0\u6750\u6599\u5bf9\u6bd4\">\u9605\u8bfb\u66f4\u591a<\/a><\/p>",
        "protected": false
    },
    "author": 1,
    "featured_media": 3409,
    "comment_status": "open",
    "ping_status": "open",
    "sticky": false,
    "template": "",
    "format": "standard",
    "meta": {
        "footnotes": ""
    },
    "categories": [
        35
    ],
    "tags": [
        140,
        136,
        137,
        67,
        139,
        138
    ],
    "class_list": [
        "post-3407",
        "post",
        "type-post",
        "status-publish",
        "format-standard",
        "has-post-thumbnail",
        "hentry",
        "category-35",
        "tag-polypropylene-bed-adhesion",
        "tag-pp-3d",
        "tag-pp-build-plate",
        "tag-pppro-2",
        "tag-pp",
        "infinite-scroll-item",
        "generate-columns",
        "tablet-grid-50",
        "mobile-grid-100",
        "grid-parent",
        "grid-33"
    ],
    "_links": {
        "self": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3407",
                "targetHints": {
                    "allow": [
                        "GET"
                    ]
                }
            }
        ],
        "collection": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts"
            }
        ],
        "about": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/types\/post"
            }
        ],
        "author": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/users\/1"
            }
        ],
        "replies": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/comments?post=3407"
            }
        ],
        "version-history": [
            {
                "count": 5,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3407\/revisions"
            }
        ],
        "predecessor-version": [
            {
                "id": 4025,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3407\/revisions\/4025"
            }
        ],
        "wp:featuredmedia": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/media\/3409"
            }
        ],
        "wp:attachment": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/media?parent=3407"
            }
        ],
        "wp:term": [
            {
                "taxonomy": "category",
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/categories?post=3407"
            },
            {
                "taxonomy": "post_tag",
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/tags?post=3407"
            }
        ],
        "curies": [
            {
                "name": "wp",
                "href": "https:\/\/api.w.org\/{rel}",
                "templated": true
            }
        ]
    }
}