{
    "id": 3426,
    "date": "2026-10-10T08:45:00",
    "date_gmt": "2026-10-10T00:45:00",
    "guid": {
        "rendered": "https:\/\/www.polive3d.com\/?p=3426"
    },
    "modified": "2026-11-09T15:20:24",
    "modified_gmt": "2026-11-09T07:20:24",
    "slug": "pp-%e6%89%93%e5%8d%b0%e9%80%9f%e5%ba%a6%e8%ae%be%e5%a4%9a%e5%b0%91%e5%90%88%e9%80%82%ef%bc%9f%e9%80%9f%e5%ba%a6%e5%af%b9%e6%89%93%e5%8d%b0%e8%b4%a8%e9%87%8f%e7%9a%84%e5%bd%b1%e5%93%8d",
    "status": "publish",
    "type": "post",
    "link": "https:\/\/www.polive3d.com\/zh_cn\/pp-%e6%89%93%e5%8d%b0%e9%80%9f%e5%ba%a6%e8%ae%be%e5%a4%9a%e5%b0%91%e5%90%88%e9%80%82%ef%bc%9f%e9%80%9f%e5%ba%a6%e5%af%b9%e6%89%93%e5%8d%b0%e8%b4%a8%e9%87%8f%e7%9a%84%e5%bd%b1%e5%93%8d\/",
    "title": {
        "rendered": "PP \u6253\u5370\u901f\u5ea6\u8bbe\u591a\u5c11\u5408\u9002\uff1f\u901f\u5ea6\u5bf9\u6253\u5370\u8d28\u91cf\u7684\u5f71\u54cd"
    },
    "content": {
        "rendered": "<h2 class=\"wp-block-heading\"><strong>What Print Speed Should Be Set for PP? The Impact of Speed on Print Quality<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Moderate steady speeds work best: PP needs time to shed heat as it cools, so consistent open-frame prints give cleaner layers than high flow.<\/p>\n\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>What print speed should be set for PP?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">For PP print speed, you can first start from <strong>40\u201360 mm\/s<\/strong>&nbsp;and verify around that range, then gradually adjust based on the print results. Usually you can appropriately reduce the outer-wall and first-layer speed to give the material more time to complete extrusion and adhesion.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">However, speed itself is not the ultimate goal.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">What truly determines print quality is<strong>whether the nozzle temperature, material flow, print speed, and cooling conditions are matched<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, for PP printing, the following approach is recommended:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Stabilize first, then increase speed.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">First find a stable temperature and extrusion state, then gradually increase the speed. This is usually easier to tune than pursuing the highest speed from the start.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>What Does Print Speed Affect?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">When the print speed increases, the time the nozzle stays at a certain position shortens, and at the same time the amount of material that needs to be extruded per unit time also increases.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This brings a series of changes.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Interlayer bonding<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">After molten material is deposited, it needs to form a bond with the next layer of material while still retaining some heat.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the print speed is too fast and the hot end cannot supply enough molten material in time, or if the material cools too quickly, interlayer bonding may be affected.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This is especially worth noting for PP parts that require higher structural strength.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Surface quality<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">If, after increasing the speed, the hot end and extrusion system cannot supply enough material, under-extrusion may occur.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Common signs include:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Irregular streaks appear on the surface;<\/li>\n\n\n\n<li>Local gaps appear;<\/li>\n\n\n\n<li>Lines become thinner at corners;<\/li>\n\n\n\n<li>Walls become discontinuous;<\/li>\n\n\n\n<li>Stringing increases.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, when you see these phenomena, you should not simply conclude &#8220;the speed is too fast&#8221;; you also need to check the nozzle temperature and actual flow at the same time.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>First-layer adhesion and warping<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">When the first-layer print speed is too fast, the time for the material to spread and compact on the build plate decreases.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the first-layer adhesion itself is unstable, further increasing the speed may raise the risk of edge lifting.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, PP printing can usually keep the first layer at a relatively low speed.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Flow load on the hot end and extrusion system<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The higher the print speed, the more material needs to be melted and extruded per unit time.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Simply put, the actual extrusion demand is related to:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>print speed \u00c3\u0097 layer height \u00c3\u0097 line width<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the required flow exceeds the hot end&#8217;s melting capacity, under-extrusion may occur.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, the maximum speed for PP printing is often limited by<strong>the hot end&#8217;s melting capacity and the actual flow capability<\/strong>, not just by the printer&#8217;s motion system.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>How to Set PP Print Speed?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Under our test conditions,<strong>PPpro\u00e2\u0084\u00a2 can use the following parameters as a starting point for small-range verification<\/strong>\uff1a<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table class=\"has-fixed-layout\"><tbody><tr><td><strong>Item<\/strong><strong><\/strong><\/td><td><strong>Reference starting point<\/strong><strong><\/strong><\/td><\/tr><tr><td>Outer wall<\/td><td>30\u201340 mm\/s<\/td><\/tr><tr><td>Inner wall \/ infill<\/td><td>40\u201360 mm\/s<\/td><\/tr><tr><td>First layer<\/td><td>20\u201330 mm\/s<\/td><\/tr><tr><td>Total flow at a 0.2 mm layer height<\/td><td>Determined by the nozzle diameter and hot-end capability<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">These values are more suitable as<strong>a testing starting point<\/strong>, rather than fixed standards that apply to all printers and models.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Different printers have different hot ends, extruders, nozzle diameters, and model structures, so the final speed needs to be verified through actual print results.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>What Should Be Adjusted First When Tuning PP Parameters?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">When printing PP, it is recommended to proceed in a relatively simple order:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>First determine the temperature \u00e2\u0086\u0092 then adjust the speed \u00e2\u0086\u0092 finally optimize cooling.<\/strong><\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Step 1: Determine the nozzle temperature<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">First ensure that the material can melt stably and extrude normally.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the temperature itself is insufficient, directly increasing the print speed can easily push the hot end into a flow bottleneck, causing under-extrusion.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Step 2: Adjust the print speed<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">After the temperature is stable, gradually increase the print speed.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If surface streaks, thinning at corners, or discontinuous extrusion begin to appear after increasing the speed, you can first lower the speed for comparison.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Step 3: Adjust the cooling fan<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Finally, adjust the cooling based on the part size, print speed, and surface performance.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Especially for the first layer and the first few layers, avoid cooling too quickly and affecting build-plate adhesion.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Why Is Acceleration Also Important?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The &#8220;print speed&#8221; in the slicer software does not mean the print head will always maintain this speed throughout the entire printing process.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Actual motion is also affected by:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Acceleration;<\/li>\n\n\n\n<li>Corner speed;<\/li>\n\n\n\n<li>Print path length;<\/li>\n\n\n\n<li>Machine motion capability;<\/li>\n\n\n\n<li>Vibration control;<\/li>\n\n\n\n<li>Minimum layer time<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">and other factors.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example, if a high print speed is set while the acceleration is also high, the print head needs to change its motion state rapidly near corners, which may cause the extrusion system&#8217;s response to lag behind the motion changes.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, for small and medium-sized printers, you can first use relatively conservative acceleration settings to make the actual motion more stable.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>When Can You Try to Increase Speed?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">If the following conditions appear, you can consider gradually increasing the print speed:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>The print surface is relatively flat;<\/li>\n\n\n\n<li>Interlayer bonding is stable;<\/li>\n\n\n\n<li>Lines at corners show no obvious thinning;<\/li>\n\n\n\n<li>Extrusion is continuous;<\/li>\n\n\n\n<li>Flow test results are stable;<\/li>\n\n\n\n<li>Hot-end temperature variation is small;<\/li>\n\n\n\n<li>First-layer and edge adhesion are normal.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Suggestions when increasing speed:<strong>Change only one variable at a time<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example, first increase from 40 mm\/s to 45 mm\/s, observe the result, then decide whether to continue increasing, rather than jumping directly from 40 mm\/s to 80 mm\/s at once.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>When Do You Need to Reduce Speed?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">If the following conditions appear, you can prioritize trying to reduce the print speed:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Obvious streaks appear on the surface;<\/li>\n\n\n\n<li>Local pits or gaps appear;<\/li>\n\n\n\n<li>Obvious thinning at corners;<\/li>\n\n\n\n<li>Under-extrusion appears on the walls;<\/li>\n\n\n\n<li>Layers are easily pulled apart;<\/li>\n\n\n\n<li>The extruder shows obvious skipped-step or &#8220;clicking&#8221; sounds.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">At this point, you can first lower the speed and then observe whether the problem disappears.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If it still persists, further check the nozzle temperature, flow, and extrusion system.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Why Can&#8217;t Small Parts Be Sped Up Indiscriminately?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Small-sized parts have another special issue:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Minimum layer time.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the model is very small, even if the print speed is set very high, the actual printing time for a single layer may still be very short.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">At this point, if the previous layer has not cooled sufficiently and the next layer begins printing, the local temperature may continue to rise, leading to:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Small pillars deform;<\/li>\n\n\n\n<li>Sharp corners soften;<\/li>\n\n\n\n<li>Details become unclear;<\/li>\n\n\n\n<li>Part dimensions change.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, small parts sometimes do not need a higher speed, but rather need to<strong>Minimum layer time<\/strong>give each layer enough cooling time.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Is the Speed Shown by the Slicer Software the Actual Speed?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Not necessarily.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The slicer software shows the target speed, but during actual printing, the printer is also affected by acceleration, corner deceleration, minimum layer time, and motion-control strategies.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, even if the slicer software shows:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>60 mm\/s<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">the print head will not necessarily maintain 60 mm\/s throughout the entire path.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, when evaluating whether the PP print speed is appropriate,<strong>the actual performance of the final printed part is more meaningful than simply staring at the speed number in the slicer software<\/strong>.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>What Should You Pay Attention to When Increasing PP Print Speed?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">You can adopt a relatively simple method:<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Step 1<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Use relatively conservative speeds, for example:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Outer wall 30\u00e2\u0080\u009340 mm\/s<\/strong><strong><br><\/strong><strong>Inner wall \/ infill 40\u00e2\u0080\u009360 mm\/s<\/strong><strong><br><\/strong><strong>First layer 20\u00e2\u0080\u009330 mm\/s<\/strong><\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Step 2<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Confirm:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>First layer is stable;<\/li>\n\n\n\n<li>Surface is normal;<\/li>\n\n\n\n<li>No obvious under-extrusion;<\/li>\n\n\n\n<li>Interlayer bonding is normal.<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Step 3<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Increase only one speed parameter at a time, for example by adding <strong>5\u201310 mm\/s<\/strong>.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Step 4<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Observe the print results.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the quality remains stable, you can continue to increase the speed slightly.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If under-extrusion or surface-quality degradation begins to appear, return to the previous stable speed.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This method makes it easier to determine the actual processing window of the printer and material than drastically increasing the speed all at once.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Summary<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">PP print speed should not be as fast as possible, but needs to be matched with<strong>nozzle temperature, flow, hot-end capability, and cooling conditions<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">You can remember the following points:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>PPpro\u00e2\u0084\u00a2 can use an outer-wall speed of 30\u00e2\u0080\u009340 mm\/s, inner-wall\/infill of 40\u00e2\u0080\u009360 mm\/s, and first layer of 20\u00e2\u0080\u009330 mm\/s as a testing starting point.<\/strong><\/li>\n\n\n\n<li>The higher the speed, the more material needs to be melted and extruded per unit time.<\/li>\n\n\n\n<li><strong>The hot end&#8217;s melting capability is an important factor limiting high-speed printing.<\/strong><\/li>\n\n\n\n<li>Appropriately reducing the first-layer speed helps stabilize first-layer adhesion.<\/li>\n\n\n\n<li>Surface streaks, thinning at corners, layers that separate easily, and extruder skipped steps can all serve as signals that you need to reduce the speed or further check the parameters.<\/li>\n\n\n\n<li><strong>Acceleration and minimum layer time also affect the final print results.<\/strong><\/li>\n\n\n\n<li>When tuning parameters, it is recommended to<strong>Change only one variable at a time<\/strong>.<\/li>\n\n\n\n<li>The most reasonable order is usually:<strong>Stabilize the temperature first, then adjust the speed, and finally optimize cooling.<\/strong><\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">For <strong>POLIVE PPpro\u2122<\/strong>, it is recommended to start with conservative speed settings, and after confirming that the temperature, flow, and interlayer bonding are stable, gradually increase the speed based on the printer&#8217;s hot-end capability and actual needs.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>\n\n<div id=\"rank-math-faq\" class=\"rank-math-block\">\n<div class=\"rank-math-list\">\n<div id=\"faq-question-polive-3426-1\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">PP \u7684\u6253\u5370\u901f\u5ea6\u8be5\u600e\u4e48\u5b9a\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u6ca1\u6709\u901a\u7528\u6570\u5b57\uff0c\u5efa\u8bae\u4ee5\u4f60\u624b\u4e0a\u8fd9\u6b3e\u7ebf\u6750\u7684\u51fa\u5382\u5efa\u8bae\u4e3a\u8d77\u70b9\uff0c\u5148\u6253\u5c0f\u4ef6\u9a8c\u8bc1\u5c42\u95f4\u7ed3\u5408\u548c\u8868\u9762\uff0c\u518d\u9010\u6b65\u8c03\u6574\u3002\u5207\u7247\u8f6f\u4ef6\u663e\u793a\u7684\u901f\u5ea6\u4e5f\u4e0d\u7b49\u4e8e\u5b9e\u9645\u901f\u5ea6\uff0c\u8fd8\u53d7\u52a0\u901f\u5ea6\u548c\u62d0\u89d2\u9650\u901f\u5f71\u54cd\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3426-2\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">\u901f\u5ea6\u4e3b\u8981\u5f71\u54cd PP \u7684\u54ea\u51e0\u4ef6\u4e8b\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u5c42\u95f4\u7ed3\u5408\u3001\u8868\u9762\u8d28\u91cf\u3001\u9996\u5c42\u9644\u7740\u4e0e\u7fd8\u8fb9\uff0c\u4ee5\u53ca\u70ed\u7aef\u548c\u6324\u51fa\u7cfb\u7edf\u7684\u6d41\u91cf\u8d1f\u8377\u3002\u901f\u5ea6\u63d0\u9ad8\u65f6\uff0c\u6700\u5bb9\u6613\u5148\u727a\u7272\u7684\u662f\u5c42\u95f4\u7ed3\u5408\u548c\u9996\u5c42\u7a33\u5b9a\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3426-3\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">\u4ec0\u4e48\u65f6\u5019\u8be5\u964d\u901f\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u5c0f\u5c3a\u5bf8\u4ef6\u3001\u8584\u58c1\u4ef6\u3001\u5927\u5e95\u677f\u9996\u5c42\u3001\u51fa\u73b0\u5c42\u7eb9\u53d1\u865a\u6216\u8fb9\u89d2\u7fd8\u8d77\u65f6\u3002PP \u9700\u8981\u5747\u5300\u51b7\u5374\uff0c\u592a\u5feb\u5bb9\u6613\u8ba9\u5c40\u90e8\u8fd8\u8f6f\u5c31\u7ee7\u7eed\u5806\u6599\uff0c\u6536\u7f29\u5e94\u529b\u53cd\u800c\u66f4\u5927\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3426-4\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">\u8c03 PP \u53c2\u6570\u5148\u52a8\u54ea\u4e00\u9879\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u5148\u786e\u5b9a\u55b7\u5634\u6e29\u5ea6\u8ba9\u7194\u4f53\u72b6\u6001\u7a33\u5b9a\uff0c\u518d\u8c03\u901f\u5ea6\uff0c\u6700\u540e\u770b\u52a0\u901f\u5ea6\u548c\u98ce\u6247\u3002\u73af\u5883\u4e0a\u4fdd\u6301\u7a7a\u8c03\u623f\u5f00\u653e\u6563\u70ed\u3001\u907f\u5f00\u7a7f\u5802\u98ce\uff0c\u6bd4\u53cd\u590d\u5fae\u8c03\u901f\u5ea6\u6570\u5b57\u66f4\u7ba1\u7528\u3002<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n<h2 class=\"wp-block-heading\"><strong>Related Reading<\/strong><strong><\/strong><\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li><a href=\"https:\/\/www.polive3d.com\/en\/pp-%e6%89%93%e5%8d%b0%e7%94%a8%e4%bb%80%e4%b9%88%e5%96%b7%e5%98%b4%ef%bc%9f%e5%96%b7%e5%98%b4%e7%a3%a8%e6%8d%9f%e4%b8%8e%e6%9d%90%e8%b4%a8%e9%80%89%e6%8b%a9\/\" data-type=\"post\" data-id=\"3422\">What Nozzle Should Be Used for PP Printing? Nozzle Wear and Material Selection<\/a><\/li>\n\n\n\n<li><a href=\"https:\/\/www.polive3d.com\/en\/pp-%e6%89%93%e5%8d%b0%e5%a0%b5%e5%a4%b4%e6%80%8e%e4%b9%88%e5%8a%9e%ef%bc%9f%e6%8c%a4%e5%87%ba%e4%b8%8d%e7%95%85%e7%9a%84%e6%8e%92%e6%9f%a5%e6%ad%a5%e9%aa%a4\/\" data-type=\"post\" data-id=\"3439\">What to Do When PP Printing Jams? Troubleshooting Steps for Poor Extrusion<\/a><\/li>\n\n\n\n<li><a href=\"https:\/\/www.polive3d.com\/en\/pp-%e6%89%93%e5%8d%b0%e4%bb%b6%e5%b1%82%e9%97%b4%e5%bc%ba%e5%ba%a6%e6%80%8e%e4%b9%88%e6%a0%b7%ef%bc%9fz-%e6%96%b9%e5%90%91%e5%bc%ba%e5%ba%a6%e6%80%8e%e4%b9%88%e6%8f%90%e5%8d%87\/\" data-type=\"post\" data-id=\"3516\">How Strong Are the Interlayer Bonds of PP Prints? How to Improve Z-Direction Strength<\/a><\/li>\n\n\n\n<li><a href=\"https:\/\/www.polive3d.com\/en\/pp-%e6%89%93%e5%8d%b0%e4%bb%b6%e8%a1%a8%e9%9d%a2%e8%b4%a8%e9%87%8f%e6%80%8e%e4%b9%88%e6%a0%b7%ef%bc%9f%e5%8d%8a%e5%93%91%e5%85%89%e8%b4%a8%e6%84%9f%e5%ae%9e%e6%b5%8b\/\" data-type=\"post\" data-id=\"3107\">How Good Is the Surface Quality of PP Prints?<\/a><\/li>\n\n\n\n<li><a href=\"https:\/\/www.polive3d.com\/en\/pp-%e6%89%93%e5%8d%b0%e4%bb%b6%e5%b0%ba%e5%af%b8%e5%87%86%e4%b8%8d%e5%87%86%ef%bc%9f%e6%94%b6%e7%bc%a9%e8%a1%a5%e5%81%bf%e4%b8%8e%e5%85%ac%e5%b7%ae%e6%8e%a7%e5%88%b6\/\" data-type=\"post\" data-id=\"3520\">Are PP Prints Dimensionally Accurate? Shrinkage Compensation and Tolerance Control<\/a><\/li>\n\n\n\n<li><a href=\"https:\/\/www.polive3d.com\/en\/3d-%e6%89%93%e5%8d%b0-pp-%e4%bb%b6%e6%80%8e%e4%b9%88%e8%ae%be%e8%ae%a1%ef%bc%9f%e5%a3%81%e5%8e%9a%e3%80%81%e5%9c%86%e8%a7%92%e3%80%81%e5%8d%a1%e6%89%a3%e4%b8%8e%e9%98%b2%e5%8f%98%e5%bd%a2%e6%8a%80\/\" data-type=\"post\" data-id=\"3710\">How to Design PP Parts for 3D Printing? Wall Thickness, Fillets, Snap Fits and Warp Prevention<\/a><\/li>\n\n\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>",
        "protected": false
    },
    "excerpt": {
        "rendered": "<p>\u672c\u6587\u89e3\u6790\u4e86PP\u6253\u5370\u901f\u5ea6\u5bf9\u5c42\u95f4\u7ed3\u5408\u3001\u8868\u9762\u8d28\u91cf\u7684\u5f71\u54cd\uff0c\u63d0\u4f9b\u4e86\u5916\u58c1\u3001\u5185\u58c1\u7b49\u53c2\u8003\u901f\u5ea6\uff0c\u5e76\u7ed9\u51fa\u5148\u5b9a\u6e29\u5ea6\u518d\u8c03\u901f\u5ea6\u7684\u5b8c\u6574\u8c03\u53c2\u987a\u5e8f\u4e0e\u63d0\u901f\u5efa\u8bae\u3002<\/p>",
        "protected": false
    },
    "author": 1,
    "featured_media": 3428,
    "comment_status": "open",
    "ping_status": "open",
    "sticky": false,
    "template": "",
    "format": "standard",
    "meta": {
        "footnotes": ""
    },
    "categories": [
        35
    ],
    "tags": [
        169,
        170,
        67,
        168,
        167,
        171
    ],
    "class_list": [
        "post-3426",
        "post",
        "type-post",
        "status-publish",
        "format-standard",
        "has-post-thumbnail",
        "hentry",
        "category-35",
        "tag-polypropylene-printing-speed",
        "tag-pp-filament-speed",
        "tag-pppro-2",
        "tag-pp",
        "infinite-scroll-item",
        "generate-columns",
        "tablet-grid-50",
        "mobile-grid-100",
        "grid-parent",
        "grid-33"
    ],
    "_links": {
        "self": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3426",
                "targetHints": {
                    "allow": [
                        "GET"
                    ]
                }
            }
        ],
        "collection": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts"
            }
        ],
        "about": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/types\/post"
            }
        ],
        "author": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/users\/1"
            }
        ],
        "replies": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/comments?post=3426"
            }
        ],
        "version-history": [
            {
                "count": 5,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3426\/revisions"
            }
        ],
        "predecessor-version": [
            {
                "id": 4019,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3426\/revisions\/4019"
            }
        ],
        "wp:featuredmedia": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/media\/3428"
            }
        ],
        "wp:attachment": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/media?parent=3426"
            }
        ],
        "wp:term": [
            {
                "taxonomy": "category",
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/categories?post=3426"
            },
            {
                "taxonomy": "post_tag",
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/tags?post=3426"
            }
        ],
        "curies": [
            {
                "name": "wp",
                "href": "https:\/\/api.w.org\/{rel}",
                "templated": true
            }
        ]
    }
}