{
    "id": 3502,
    "date": "2026-10-12T19:55:00",
    "date_gmt": "2026-10-12T11:55:00",
    "guid": {
        "rendered": "https:\/\/www.polive3d.com\/?p=3502"
    },
    "modified": "2026-11-09T15:20:16",
    "modified_gmt": "2026-11-09T07:20:16",
    "slug": "pp-%e6%89%93%e5%8d%b0%e4%bb%b6%e8%83%bd%e6%89%bf%e5%8f%97%e5%a4%9a%e5%b0%91%e6%b8%a9%e5%ba%a6%ef%bc%9fpp-%e7%9a%84%e8%80%90%e7%83%ad%e8%a1%a8%e7%8e%b0",
    "status": "publish",
    "type": "post",
    "link": "https:\/\/www.polive3d.com\/zh_cn\/pp-%e6%89%93%e5%8d%b0%e4%bb%b6%e8%83%bd%e6%89%bf%e5%8f%97%e5%a4%9a%e5%b0%91%e6%b8%a9%e5%ba%a6%ef%bc%9fpp-%e7%9a%84%e8%80%90%e7%83%ad%e8%a1%a8%e7%8e%b0\/",
    "title": {
        "rendered": "PP \u6253\u5370\u4ef6\u80fd\u627f\u53d7\u591a\u5c11\u6e29\u5ea6\uff1fPP \u7684\u8010\u70ed\u8868\u73b0"
    },
    "content": {
        "rendered": "<h2 class=\"wp-block-heading\"><strong>How Much Temperature Can PP Prints Withstand? PP&#8217;s Heat-Resistance Performance<\/strong><strong><\/strong><\/h2>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<p class=\"wp-block-paragraph\">The heat resistance of PP prints cannot be summed up by a single temperature.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Melting point, heat deflection temperature (HDT), Vicat softening point, and long-term service temperature<\/strong>describe different temperature characteristics, and the actual performance is also affected by load, heating time, and environmental conditions.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, to judge whether a PP print can be used in high-temperature scenarios, you shouldn&#8217;t look only at the material&#8217;s melting point, but should combine three core conditions:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>How high is the temperature? How much load does it bear? For how long?<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For an actual part, these three conditions are usually more meaningful than a single &#8216;maximum temperature&#8217; number.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Don&#8217;t Confuse the Three Temperature Concepts<\/strong><strong><\/strong><\/h2>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>1. Melting point<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The melting point is the temperature range at which a material undergoes a melting transition.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">PP is a semi-crystalline thermoplastic, and the melting temperature varies among different PP formulations.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Note:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>The melting point is not the part&#8217;s long-term service temperature.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A material&#8217;s mechanical properties may already change significantly as temperature rises before it reaches the melting point, so you cannot simply assume &#8216;as long as the melting point isn&#8217;t reached, it can be used long-term&#8217;.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>2. Heat deflection temperature (HDT)<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">HDT is the temperature at which a standard specimen reaches a specified amount of deflection under specified test conditions and a specified load.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, HDT is not a fixed temperature entirely detached from test conditions.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">In the test:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Load<\/li>\n\n\n\n<li>Specimen dimensions<\/li>\n\n\n\n<li>Test method<\/li>\n\n\n\n<li>Deflection criteria<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">all affect the final result.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This is also why the same material may yield different HDT values under different test conditions.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>3. Vicat softening point<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The Vicat softening point evaluates a material&#8217;s softening behavior during heating through a specified penetration test.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Both it and HDT can describe a material&#8217;s performance change during heating, but their test principles and criteria differ.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore,<strong>HDT and Vicat also cannot simply be substituted for each other.<\/strong><\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Why Can&#8217;t the Melting Point Be Used Directly as the Service Temperature?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">This is one of the most important points when understanding PP&#8217;s heat resistance.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Assuming a material has a high melting point does not mean it can still maintain its original mechanical properties when approaching that temperature.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For a load-bearing part, as temperature rises, the material&#8217;s stiffness and load-carrying capacity may gradually decline.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>The melting point answers &#8216;when melting transition occurs,&#8217; not &#8216;how much temperature the part can endure long-term.&#8217;<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If you need to judge whether a PP print can be used in a real high-temperature environment, you should further consider HDT, deformation under long-term load, and actual service conditions.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Heat Resistance Without Load Differs Greatly from Heat Resistance Under Load<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">This is a problem especially easy to overlook in 3D-printed functional parts.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Some parts bear almost no mechanical load in high-temperature environments, such as:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Decorative covers<\/li>\n\n\n\n<li>Some enclosures<\/li>\n\n\n\n<li>Storage boxes<\/li>\n\n\n\n<li>Non-load-bearing structures<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">While other parts still need to bear sustained loads in high-temperature environments, such as:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Hooks<\/li>\n\n\n\n<li>Snaps<\/li>\n\n\n\n<li>Brackets<\/li>\n\n\n\n<li>Connectors<\/li>\n\n\n\n<li>Fixtures<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">These two types of parts have completely different heat-resistance requirements.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Why Can a Part &#8216;Not Melt&#8217; Yet Still Deform at High Temperatures?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">One of the reasons is<strong>creep.<\/strong>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Polymers under sustained load may develop slow, continuous deformation over time even if the temperature hasn&#8217;t reached the melting point.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The higher the temperature, the more this time-dependent deformation usually needs attention.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example, a PP hook that can bear a certain weight at first does not mean it will keep the same shape after carrying load continuously for days or months at higher temperatures.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, for load-bearing parts, don&#8217;t just ask:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">&#8216;Has this temperature exceeded PP&#8217;s melting point?&#8217;<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">You should ask instead:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>&#8216;Will this part, under this load at this temperature for this long, develop unacceptable deformation?&#8217;<\/strong><\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>How to Compare the Heat Resistance of PP with PLA, PETG, and ABS?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Different materials&#8217; heat resistance needs to be compared using specific metrics, not ranked simply by a single melting or softening temperature.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>PP<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">PP is a semi-crystalline polymer that usually has good heat-resistance potential while retaining some toughness.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For parts that need to balance:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Heat-resistant<\/li>\n\n\n\n<li>toughness<\/li>\n\n\n\n<li>chemical stability<\/li>\n\n\n\n<li>low density<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">, PP is a material worth considering.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>PLA<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">PLA has a lower printing temperature and good rigidity, but its heat resistance is relatively limited. At higher ambient temperatures, PLA prints may soften and deform earlier.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, PLA is better suited for applications with relatively limited temperature requirements.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>PETG<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">PETG offers a certain balance among heat resistance, toughness, and printability, suiting many general functional parts.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">But its specific heat-resistance capability still needs to be judged from the material grade and test data.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>ABS<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">ABS is commonly used for functional and engineering prints, with certain advantages in heat resistance and mechanical performance.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">But ABS&#8217;s shrinkage and warping during printing can also affect the final part&#8217;s dimensional stability and real-world performance.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, rather than simply asking &#8216;is PP more heat-resistant than PETG or ABS,&#8217; it&#8217;s better to target the specific:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>temperature + load + time<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">for testing and comparison.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>How to Verify High-Temperature Scenarios?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">If a PP print needs to be used in a real high-temperature environment, it&#8217;s recommended to test it as closely as possible to actual service conditions.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>1. Constant-temperature test<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Place the print in an environment at the set temperature and observe after a specified time:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Size changes<\/li>\n\n\n\n<li>Warping<\/li>\n\n\n\n<li>Softening<\/li>\n\n\n\n<li>Permanent deformation<\/li>\n\n\n\n<li>Surface changes<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">This helps judge the part&#8217;s stability in high-temperature environments.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>2. High-temperature test with load<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">If the actual part needs to bear load during use, it&#8217;s best to add the corresponding mechanical load during testing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Hook \u2192 high-temperature environment + actual weight<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Bracket \u2192 high-temperature environment + actual load<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Snap \u2192 high-temperature environment + assembly stress<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This kind of test is closer to real usage than simply putting the part in an oven.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>3. Thermal cycling test<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">If the product needs to undergo repeated temperature changes, thermal cycling can also be performed.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Room temperature \u2192 high temperature \u2192 cooling \u2192 room temperature<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">After repeated cycling, observe:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Cracks<\/li>\n\n\n\n<li>Deformation<\/li>\n\n\n\n<li>Size changes<\/li>\n\n\n\n<li>Interlayer failure<\/li>\n\n\n\n<li>Joint failure<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Thermal cycling helps reveal problems that a single constant-temperature test may miss.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>What Does a 100\u00b0C Boiling-Water Test Show?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">For PP 3D prints, a 100\u00b0C boiling-water test can serve as an intuitive short-term high-temperature verification.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example, observe whether the print shows the following after boiling-water immersion:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Obvious softening<\/li>\n\n\n\n<li>Severe deformation<\/li>\n\n\n\n<li>Cracking<\/li>\n\n\n\n<li>Size changes<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">But it should be noted that:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>A 100\u00b0C boiling-water test is not the same as a 100\u00b0C long-term service test.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Conditions such as water-bath temperature, heating method, duration, and whether the part is loaded differ from the actual service environment.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, such tests are better suited as<strong>application verification under short-term high-temperature conditions<\/strong>, rather than directly defining the material&#8217;s long-term service temperature.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For POLIVE PPpro\u2122, if it needs to be used in specific high-temperature applications, we still recommend verification with the actual part, actual load, and actual service time.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Clarify Three Conditions First When Selecting Materials for High Temperatures<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Facing a high-temperature application, you can first answer three questions:<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Temperature<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">How much temperature does the part actually need to withstand?<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Is it:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>60\u00b0C<\/li>\n\n\n\n<li>80\u00b0C<\/li>\n\n\n\n<li>100\u00b0C<\/li>\n\n\n\n<li>or even higher?<\/li>\n<\/ul>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Load<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Does the part bear mechanical load at this temperature?<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Is it static, dynamic, or repeated load?<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Time<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">How long does the high-temperature state last?<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Is it:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>A few minutes<\/li>\n\n\n\n<li>A few hours<\/li>\n\n\n\n<li>A few days<\/li>\n\n\n\n<li>or long-term continuous use?<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Only by pinning down these three conditions can you more easily judge whether the material and structure are suitable.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>PP Prints&#8217; Heat Resistance Depends on More Than the Material Alone<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">For FDM prints, the final high-temperature performance is actually the result of multiple factors acting together:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>material formulation + print parameters + print orientation + part structure + temperature + load + time<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Different parts printed from the same PP filament may also perform completely differently at high temperatures.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A thin-walled, load-bearing snap and a load-free thick-walled enclosure, even with identical PP material, cannot be judged by the same &#8216;heat-resistance temperature&#8217;.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, material selection for high-temperature applications should start from<strong>actual service conditions<\/strong>, rather than searching for a single maximum temperature detached from test conditions.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Summary<\/strong><strong><\/strong><\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Melting point, HDT, Vicat softening point, and long-term service temperature are not the same concept.<\/strong><\/li>\n\n\n\n<li>The melting point cannot be used directly as the long-term service temperature of a PP print.<\/li>\n\n\n\n<li>Load-bearing PP parts need special attention to creep and long-term deformation at high temperatures.<\/li>\n\n\n\n<li>The heat resistance of PP, PLA, PETG, and ABS should be compared in the context of specific test conditions and application scenarios.<\/li>\n\n\n\n<li>High-temperature verification should ideally consider<strong>temperature, load, and time<\/strong>.<\/li>\n\n\n\n<li>Constant-temperature, high-temperature-with-load, and thermal-cycling tests can help determine whether a print is suitable for real high-temperature applications.<\/li>\n\n\n\n<li>A 100\u00b0C boiling-water test can serve as short-term high-temperature application verification, but it does not directly equal long-term 100\u00b0C service capability.<\/li>\n\n\n\n<li>For a specific PP material, selection should be based on its corresponding actual test data, not just general PP parameters.<\/li>\n<\/ul>\n\n\n<div id=\"rank-math-faq\" class=\"rank-math-block\">\n<div class=\"rank-math-list\">\n<div id=\"faq-question-polive-3502-1\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">PP \u6253\u5370\u4ef6\u80fd\u627f\u53d7\u591a\u5c11\u6e29\u5ea6\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u4e00\u4e2a\u6e29\u5ea6\u8bf4\u4e0d\u6e05\uff0c\u8981\u5206\u7194\u70b9\u3001\u70ed\u53d8\u5f62\u6e29\u5ea6\u3001\u7ef4\u5361\u8f6f\u5316\u70b9\u4e09\u4e2a\u6982\u5ff5\uff0c\u800c\u4e14\u65e0\u8d1f\u8f7d\u8010\u70ed\u548c\u5e26\u8d1f\u8f7d\u8010\u70ed\u5dee\u522b\u5f88\u5927\u3002\u7194\u70b9\u4e0d\u80fd\u76f4\u63a5\u5f53\u6210\u4f7f\u7528\u6e29\u5ea6\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3502-2\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">\u4e3a\u4ec0\u4e48\u6ca1\u7194\u5316\u4e5f\u4f1a\u9ad8\u6e29\u53d8\u5f62\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u534a\u7ed3\u6676\u6750\u6599\u5728\u8fdc\u4f4e\u4e8e\u7194\u70b9\u65f6\u5c31\u53ef\u80fd\u8f6f\u5316\uff0c\u5c24\u5176\u96f6\u4ef6\u6301\u7eed\u53d7\u529b\u7684\u65f6\u5019\u3002\u6240\u4ee5\u5224\u65ad\u80fd\u4e0d\u80fd\u7528\u5728\u70ed\u73af\u5883\uff0c\u8981\u770b\u5b9e\u9645\u8f7d\u8377\u548c\u5b9e\u6d4b\u7ed3\u679c\uff0c\u4e0d\u662f\u770b\u6750\u6599\u5316\u4e0d\u5316\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3502-3\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">100\u00b0C \u6cb8\u6c34\u6d4b\u8bd5\u8bf4\u660e\u4ec0\u4e48\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u8bf4\u660e PPpro\u2122 \u5728\u8fd9\u4e2a\u6761\u4ef6\u4e0b\u4e0d\u4f1a\u7acb\u523b\u8f6f\u5316\u53d8\u5f62\uff0c\u4f46\u4e0d\u80fd\u5916\u63a8\u6210\u6240\u6709\u9ad8\u6e29\u5de5\u51b5\u90fd\u53ef\u7528\uff1b\u58c1\u539a\u3001\u5c42\u95f4\u7ed3\u5408\u548c\u662f\u5426\u627f\u91cd\u90fd\u4f1a\u6539\u53d8\u7ed3\u679c\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3502-4\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">\u600e\u4e48\u9a8c\u8bc1\u81ea\u5df1\u7684\u9ad8\u6e29\u573a\u666f\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u7528\u771f\u5b9e\u96f6\u4ef6\u3001\u771f\u5b9e\u6e29\u5ea6\u3001\u771f\u5b9e\u8d1f\u8f7d\u548c\u771f\u5b9e\u65f6\u957f\u53bb\u6d4b\uff0c\u51b7\u5374\u540e\u590d\u6d4b\u5c3a\u5bf8\u4e0e\u88c5\u914d\uff1b\u548c PLA\u3001PETG\u3001ABS \u5728\u540c\u4e00\u6761\u4ef6\u4e0b\u5bf9\u6bd4\uff0c\u6bd4\u67e5\u53c2\u6570\u8868\u53ef\u9760\u3002<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n<h3 class=\"wp-block-heading\"><strong>Related Reading<\/strong><strong><\/strong><\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Can PP 3D Printed Parts Hold Boiling Water? POLIVE PPpro\u2122 100\u00b0C Boiling Water Test<\/li>\n\n\n\n<li>How Long Do PP Prints Last? Ageing and Service Life of PP<\/li>\n\n\n\n<li>Are PP Prints Strong? How to Assess PP&#8217;s Mechanical Properties<\/li>\n\n\n\n<li>Can 3D printing be used to produce automotive parts? Applications of PP (polypropylene) in the automotive sector<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>",
        "protected": false
    },
    "excerpt": {
        "rendered": "<p>\u672c\u6587\u89e3\u6790PP\u6253\u5370\u4ef6\u7684\u8010\u70ed\u8868\u73b0\uff0c\u5398\u6e05\u7194\u70b9\u4e0e\u4f7f\u7528\u6e29\u5ea6\u7684\u8bef\u533a\uff0c\u6307\u51fa\u8bc4\u4f30\u8010\u70ed\u9700\u7efc\u5408\u6e29\u5ea6\u3001\u8f7d\u8377\u4e0e\u65f6\u95f4\uff0c\u5e76\u5bf9\u6bd4\u4e86PP\u4e0ePLA\u3001PETG\u3001ABS\u7684\u5dee\u5f02\u3002<\/p>",
        "protected": false
    },
    "author": 1,
    "featured_media": 3504,
    "comment_status": "open",
    "ping_status": "open",
    "sticky": false,
    "template": "",
    "format": "standard",
    "meta": {
        "footnotes": ""
    },
    "categories": [
        35
    ],
    "tags": [
        193,
        67,
        197,
        194,
        196,
        195
    ],
    "class_list": [
        "post-3502",
        "post",
        "type-post",
        "status-publish",
        "format-standard",
        "has-post-thumbnail",
        "hentry",
        "category-35",
        "tag-polypropylene-heat-resistance",
        "tag-pppro-2",
        "tag-pp",
        "infinite-scroll-item",
        "generate-columns",
        "tablet-grid-50",
        "mobile-grid-100",
        "grid-parent",
        "grid-33"
    ],
    "_links": {
        "self": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3502",
                "targetHints": {
                    "allow": [
                        "GET"
                    ]
                }
            }
        ],
        "collection": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts"
            }
        ],
        "about": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/types\/post"
            }
        ],
        "author": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/users\/1"
            }
        ],
        "replies": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/comments?post=3502"
            }
        ],
        "version-history": [
            {
                "count": 4,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3502\/revisions"
            }
        ],
        "predecessor-version": [
            {
                "id": 4014,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3502\/revisions\/4014"
            }
        ],
        "wp:featuredmedia": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/media\/3504"
            }
        ],
        "wp:attachment": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/media?parent=3502"
            }
        ],
        "wp:term": [
            {
                "taxonomy": "category",
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/categories?post=3502"
            },
            {
                "taxonomy": "post_tag",
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/tags?post=3502"
            }
        ],
        "curies": [
            {
                "name": "wp",
                "href": "https:\/\/api.w.org\/{rel}",
                "templated": true
            }
        ]
    }
}