{
    "id": 3516,
    "date": "2026-10-13T14:08:00",
    "date_gmt": "2026-10-13T06:08:00",
    "guid": {
        "rendered": "https:\/\/www.polive3d.com\/?p=3516"
    },
    "modified": "2026-11-09T15:20:11",
    "modified_gmt": "2026-11-09T07:20:11",
    "slug": "pp-%e6%89%93%e5%8d%b0%e4%bb%b6%e5%b1%82%e9%97%b4%e5%bc%ba%e5%ba%a6%e6%80%8e%e4%b9%88%e6%a0%b7%ef%bc%9fz-%e6%96%b9%e5%90%91%e5%bc%ba%e5%ba%a6%e6%80%8e%e4%b9%88%e6%8f%90%e5%8d%87",
    "status": "publish",
    "type": "post",
    "link": "https:\/\/www.polive3d.com\/zh_cn\/pp-%e6%89%93%e5%8d%b0%e4%bb%b6%e5%b1%82%e9%97%b4%e5%bc%ba%e5%ba%a6%e6%80%8e%e4%b9%88%e6%a0%b7%ef%bc%9fz-%e6%96%b9%e5%90%91%e5%bc%ba%e5%ba%a6%e6%80%8e%e4%b9%88%e6%8f%90%e5%8d%87\/",
    "title": {
        "rendered": "PP \u6253\u5370\u4ef6\u5c42\u95f4\u5f3a\u5ea6\u600e\u4e48\u6837\uff1fZ \u65b9\u5411\u5f3a\u5ea6\u600e\u4e48\u63d0\u5347"
    },
    "content": {
        "rendered": "<h2 class=\"wp-block-heading\"><strong>How Strong Are the Interlayer Bonds of PP Prints? How to Improve Z-Direction Strength<\/strong><strong><\/strong><\/h2>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<p class=\"wp-block-paragraph\">FDM printed parts are inherently somewhat anisotropic, so mechanical properties can differ across printing directions.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Among them,<strong>the Z direction is usually the one to watch<\/strong>, because Z-direction loads are more likely to act on the interface between adjacent printed layers.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">PP shares this characteristic.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For PP 3D printing, one key to improving Z-direction performance is to achieve fuller, more stable fusion between adjacent printed layers, rather than simply stacking one layer of material on top of another.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>How Does Interlayer Bonding Form?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">During FDM printing, new molten material is extruded and deposited onto the surface of the previously printed layer.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Under ideal conditions, the freshly extruded melt applies some thermal effect to the previous layer&#8217;s surface, keeping the interfacial temperature in a range that favors material fusion.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Then molecular chain diffusion and entanglements occur between the two layers, and as the material cools, interlayer bonding is ultimately formed.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the previous layer has cooled too quickly, or the newly extruded material cannot provide enough heat and contact time, interlayer fusion may be insufficient.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This means:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Interlayer strength depends not only on the material itself but is also closely tied to the thermal history during printing.<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Key factors to watch:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Interfacial temperature<\/li>\n\n\n\n<li>Melt temperature<\/li>\n\n\n\n<li>Contact time<\/li>\n\n\n\n<li>Material flowability<\/li>\n\n\n\n<li>Cooling rate<\/li>\n<\/ul>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Several Key Factors for Improving PP Interlayer Strength<\/strong><strong><\/strong><\/h2>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>1. Printing temperature<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Printing temperature affects melt flowability and interlayer fusion.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Within the material&#8217;s allowable processing range, moderately raising the nozzle temperature helps maintain sufficient melt heat, enabling fuller fusion between new and old printed layers.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">But this does not mean higher is always better.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Excessively high temperature may lead to:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Increased stringing<\/li>\n\n\n\n<li>Reduced surface quality<\/li>\n\n\n\n<li>Worse dimensional stability<\/li>\n\n\n\n<li>Material thermal degradation<\/li>\n\n\n\n<li>Other extrusion anomalies<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, a more reasonable approach is to find the processing window suited to the specific PP material through temperature testing.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>2. Print speed<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Print speed also affects the interlayer thermal history.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If print speed is too high, the heat and fusion time received per unit area may change, affecting interlayer bonding.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Moderately reducing print speed, especially where better interlayer bonding is needed, can be one optimization direction.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">However, the actual effect also depends on:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Nozzle temperature<\/li>\n\n\n\n<li>Hotend melting capacity<\/li>\n\n\n\n<li>Floor height<\/li>\n\n\n\n<li>Print path<\/li>\n\n\n\n<li>Cooling conditions<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, speed cannot be judged in isolation from other parameters.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>3. Layer height<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Layer height changes the geometry and heat-transfer conditions of each layer of material.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When layer height is too large, attention is needed on the contact area between single layers and the interlayer fusion state.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, when improving Z-direction performance, comparative testing across different layer heights can help find the parameter combination suited to the specific material and printer.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Lower layer height is not always better; ultimately it still requires balancing print quality, print efficiency, and actual mechanical performance.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>4. Thermal environment<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The printing environment temperature also affects the cooling rate during PP printing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the printing environment is cool or there is noticeable airflow, already-printed layers may cool rapidly, affecting the fusion of subsequent layers and the overall part&#8217;s thermal shrinkage behavior.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For larger PP prints, a stable printing environment is especially important.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, depending on the printer and part size, consider:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Enclosed print chamber<\/li>\n\n\n\n<li>Reduce direct cold drafts<\/li>\n\n\n\n<li>Stable ambient temperature<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">But not all PP printing requires an enclosed chamber; the specific need depends on the material, part size, and environmental conditions.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>5. Cooling strategy<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The cooling fan directly affects the cooling rate of printed layers.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For PP printing, if cooling is too strong, it may rapidly cool the just-extruded material, making it harder to maintain a high interlayer interface temperature.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, when optimizing interlayer bonding, reduce unnecessary forced cooling and adjust fan strategy based on the specific material.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">But completely turning off the fan is not necessarily suitable for all printing situations.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Cooling strategy still needs to balance:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>interlayer fusion, surface quality, bridging ability, and dimensional stability<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Print Orientation: Keep the Main Load Direction Away from Weak Interlayer Interfaces<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">If a part mainly experiences tensile or bending loads in actual use, print orientation is a very important design variable.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">FDM printed parts do not have exactly the same properties in every direction.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the main load acts directly on the interlayer interface, the risk of delamination or interlayer failure may increase.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, when designing functional parts, try to align the main load path with the filament deposition direction of the printed layers, while reducing situations where critical loads act directly on interlayer interfaces.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example, for certain hooks, brackets, and connectors, changing the part&#8217;s placement orientation can improve how loads are borne.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">But the specific best orientation depends on:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Load direction<\/li>\n\n\n\n<li>Part geometry<\/li>\n\n\n\n<li>Print path<\/li>\n\n\n\n<li>Wall thickness<\/li>\n\n\n\n<li>Interlayer bonding<\/li>\n\n\n\n<li>Actual usage<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">So you cannot simply assume that one placement orientation is always stronger for all parts.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>What If Z-Direction Loading Cannot Be Avoided?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Not all parts can solve the problem by changing print orientation.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">When critical structures must bear Z-direction loads, structural design can reduce pressure on interlayer interfaces.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example:<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Increase the loaded cross-section<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Increase wall thickness or local cross-sectional area to reduce stress per unit area.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Add reinforcing ribs<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">For brackets, enclosures, and connectors, reinforcing ribs can redirect the load-transfer path.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Optimize fillets<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Avoid sharp right-angle transitions to reduce local stress concentration.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Adjust structural orientation<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Sometimes you don&#8217;t need to change the whole part&#8217;s print orientation\u2014redesigning a local structure alone can improve the load path.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore,<strong>material, printing process, and structural design should be combined to address Z-direction strength issues.<\/strong><\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>How to Test PP Interlayer Strength?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">One fairly intuitive method is to print tensile specimens in different orientations and compare them.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Step 1: Keep printing parameters consistent<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">For example, fix:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Material<\/li>\n\n\n\n<li>Nozzle temperature<\/li>\n\n\n\n<li>Floor height<\/li>\n\n\n\n<li>Print speed<\/li>\n\n\n\n<li>Number of wall lines<\/li>\n\n\n\n<li>Fill rate<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Only change the specimen&#8217;s print orientation.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Step 2: Perform tensile tests separately<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Compare the following across specimens from different orientations:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Maximum tensile strength<\/li>\n\n\n\n<li>Elongation at break<\/li>\n\n\n\n<li>Fracture location<\/li>\n\n\n\n<li>Failure mode<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">This makes it easier to directly observe the anisotropy introduced by print orientation.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\"><strong>Step 3: Observe the fracture surface<\/strong><strong><\/strong><\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Fracture surface morphology can also provide some information.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If fracture occurs mainly along the interlayer interface, it indicates the interlayer region may be a critical weak point.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If the material shows more pronounced plastic deformation, the failure mechanism may be different.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">However, fracture observation is better used as a supplementary analysis and cannot replace standardized mechanical testing on its own.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>How to Compare Z and XY Directions More Accurately?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">If you want meaningful comparison data, the most important thing is to control variables.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For example:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Same material + same printer + same print parameters + same specimen dimensions + different print orientations<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Only then can you clearly observe the effect of print orientation itself.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">At the same time, the test report should ideally record:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Material grade<\/li>\n\n\n\n<li>Printer model<\/li>\n\n\n\n<li>Nozzle temperature<\/li>\n\n\n\n<li>Hotbed temperature<\/li>\n\n\n\n<li>Floor height<\/li>\n\n\n\n<li>Print speed<\/li>\n\n\n\n<li>Cooling settings<\/li>\n\n\n\n<li>Number of wall lines<\/li>\n\n\n\n<li>Fill rate<\/li>\n\n\n\n<li>Print orientation<\/li>\n\n\n\n<li>Testing Standards<\/li>\n\n\n\n<li>Test environment<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Only then will the resulting data be easier to reproduce and compare.<\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Why Is PP&#8217;s Interlayer Strength Especially Worth Attention?<\/strong><strong><\/strong><\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">PP itself has good flexibility and toughness, but the final performance of FDM printed parts depends on more than the material alone.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For an actual PP part:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Material properties \u2260 printed-part properties<\/strong><\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The final mechanical behavior is also influenced by the microstructure formed during printing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Especially under Z-direction loading, interlayer bonding can become a key factor determining the part&#8217;s final failure mode.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Therefore, for PP printed parts that must bear loads, merely knowing PP&#8217;s material parameters is not enough.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">You also need to know:<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>how the part actually performs under your specific print parameters and orientation.<\/strong><\/p>\n\n\n\n<hr class=\"wp-block-separator has-alpha-channel-opacity\"\/>\n\n\n\n<h2 class=\"wp-block-heading\"><strong>Summary<\/strong><strong><\/strong><\/h2>\n\n\n\n<ul class=\"wp-block-list\">\n<li>FDM printed parts are anisotropic, and Z-direction performance is usually the part that needs close attention.<\/li>\n\n\n\n<li>The interlayer strength of PP prints depends on<strong>interfacial temperature, melt temperature, contact time, and cooling rate<\/strong>and other thermal-history factors.<\/li>\n\n\n\n<li>Printing temperature, print speed, layer height, thermal environment, and cooling strategy can all serve as directions for optimizing interlayer bonding.<\/li>\n\n\n\n<li>Choosing a sensible print orientation is an important way to reduce Z-direction loading risk.<\/li>\n\n\n\n<li>If Z-direction loading cannot be avoided, structural design measures such as increasing cross-section, adding ribs, and using fillets can improve load distribution.<\/li>\n\n\n\n<li>Testing standard specimens with identical parameters but different print orientations gives a direct evaluation of a print&#8217;s anisotropy.<\/li>\n\n\n\n<li>For actual functional parts, consider comprehensively<strong>material, printing process, print orientation, and part structure<\/strong>, rather than looking only at the material&#8217;s own strength.<\/li>\n<\/ul>\n\n\n<div id=\"rank-math-faq\" class=\"rank-math-block\">\n<div class=\"rank-math-list\">\n<div id=\"faq-question-polive-3516-1\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">PP \u6253\u5370\u4ef6 Z \u65b9\u5411\u4e3a\u4ec0\u4e48\u504f\u5f31\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>FDM \u672c\u8eab\u5404\u5411\u5f02\u6027\uff0c\u5c42\u4e0e\u5c42\u9760\u7194\u4f53\u91cd\u65b0\u7f20\u7ed3\u7ed3\u5408\uff0c\u5f3a\u5ea6\u901a\u5e38\u4f4e\u4e8e XY \u5e73\u9762\u5185\u7684\u8fde\u7eed\u6324\u51fa\u8def\u5f84\u3002PP \u7684\u534a\u7ed3\u6676\u6536\u7f29\u8ba9\u8fd9\u4e00\u70b9\u66f4\u503c\u5f97\u5173\u6ce8\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3516-2\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">\u63d0\u5347\u5c42\u95f4\u7ed3\u5408\u5148\u770b\u54ea\u51e0\u9879\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u55b7\u5634\u6e29\u5ea6\u3001\u6253\u5370\u901f\u5ea6\u3001\u5c42\u9ad8\u3001\u70ed\u73af\u5883\u548c\u51b7\u5374\u7b56\u7565\u3002\u8ba9\u4e0a\u4e00\u5c42\u8fd8\u4fdd\u6709\u8db3\u591f\u70ed\u91cf\u65f6\u4e0b\u4e00\u5c42\u5c31\u53e0\u4e0a\u53bb\uff0c\u540c\u65f6\u907f\u514d\u5c40\u90e8\u6025\u51b7\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3516-3\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">\u4e3b\u53d7\u529b\u65b9\u5411\u907f\u4e0d\u5f00 Z \u600e\u4e48\u529e\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u52a0\u5927\u53d7\u529b\u622a\u9762\u3001\u589e\u52a0\u58c1\u539a\u548c\u586b\u5145\u3001\u7528\u5706\u89d2\u8fc7\u6e21\u6d88\u9664\u5e94\u529b\u96c6\u4e2d\uff0c\u5fc5\u8981\u65f6\u6539\u53d8\u88c5\u914d\u7ed3\u6784\u8ba9\u8f7d\u8377\u8f6c\u4e3a\u538b\u5e94\u529b\u800c\u4e0d\u662f\u53bb\u6495\u5c42\u3002<\/p>\n\n<\/div>\n<\/div>\n<div id=\"faq-question-polive-3516-4\" class=\"rank-math-list-item\">\n<h3 class=\"rank-math-question\">\u5f00\u653e\u6563\u70ed\u4f1a\u4e0d\u4f1a\u524a\u5f31\u5c42\u95f4\u7ed3\u5408\uff1f<\/h3>\n<div class=\"rank-math-answer\">\n\n<p>\u6211\u4eec\u5b9e\u64cd\u5c31\u662f\u5f00\u653e\u6253\u5370\uff1aPP \u51b7\u5374\u8981\u6563\u6389\u5927\u91cf\u70ed\uff0c\u7a7a\u8c03\u623f\u5f00\u95e8\u5f00\u76d6\u66f4\u5229\u4e8e\u6574\u4f53\u5747\u5300\u5b9a\u578b\u3002\u5173\u952e\u662f\u5747\u5300\u800c\u4e0d\u662f\u4fdd\u6e29\uff0c\u914d\u5408\u58c1\u539a\u5747\u5300\u548c\u907f\u5f00\u7a7f\u5802\u98ce\uff0c\u5c42\u95f4\u53cd\u800c\u66f4\u7a33\u3002<\/p>\n\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n\n\n<h3 class=\"wp-block-heading\"><strong>Related Reading<\/strong><strong><\/strong><\/h3>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Are PP Prints Strong? How to Assess PP&#8217;s Mechanical Properties<\/li>\n\n\n\n<li>Does PP Printing Require an Enclosure? The Impact of Ambient Temperature on Printing<\/li>\n\n\n\n<li>How to Configure PP 3D Printing Settings? PPpro\u2122 Parameter Guide<\/li>\n\n\n\n<li>How to Design PP Parts for 3D Printing? Wall Thickness, Fillets, Snap Fits and Warp Prevention<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>",
        "protected": false
    },
    "excerpt": {
        "rendered": "<p>\u672c\u6587\u89e3\u6790PP\u6253\u5370\u4ef6\u5c42\u95f4\u5f3a\u5ea6\u4e0eZ\u65b9\u5411\u6027\u80fd\uff0c\u63a2\u8ba8\u6e29\u5ea6\u3001\u901f\u5ea6\u53ca\u51b7\u5374\u5bf9\u5c42\u95f4\u7ed3\u5408\u7684\u5f71\u54cd\uff0c\u5e76\u4ecb\u7ecd\u4e86\u901a\u8fc7\u4f18\u5316\u6253\u5370\u65b9\u5411\u4e0e\u7ed3\u6784\u8bbe\u8ba1\u6765\u63d0\u5347Z\u5411\u5f3a\u5ea6\u7684\u65b9\u6cd5\u3002<\/p>",
        "protected": false
    },
    "author": 1,
    "featured_media": 3518,
    "comment_status": "open",
    "ping_status": "open",
    "sticky": false,
    "template": "",
    "format": "standard",
    "meta": {
        "footnotes": ""
    },
    "categories": [
        35
    ],
    "tags": [
        207,
        210,
        67,
        208,
        211,
        209
    ],
    "class_list": [
        "post-3516",
        "post",
        "type-post",
        "status-publish",
        "format-standard",
        "has-post-thumbnail",
        "hentry",
        "category-35",
        "tag-polypropylene-layer-adhesion",
        "tag-pp-z",
        "tag-pppro-2",
        "tag-pp",
        "infinite-scroll-item",
        "generate-columns",
        "tablet-grid-50",
        "mobile-grid-100",
        "grid-parent",
        "grid-33"
    ],
    "_links": {
        "self": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3516",
                "targetHints": {
                    "allow": [
                        "GET"
                    ]
                }
            }
        ],
        "collection": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts"
            }
        ],
        "about": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/types\/post"
            }
        ],
        "author": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/users\/1"
            }
        ],
        "replies": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/comments?post=3516"
            }
        ],
        "version-history": [
            {
                "count": 4,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3516\/revisions"
            }
        ],
        "predecessor-version": [
            {
                "id": 4011,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/posts\/3516\/revisions\/4011"
            }
        ],
        "wp:featuredmedia": [
            {
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/media\/3518"
            }
        ],
        "wp:attachment": [
            {
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/media?parent=3516"
            }
        ],
        "wp:term": [
            {
                "taxonomy": "category",
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/categories?post=3516"
            },
            {
                "taxonomy": "post_tag",
                "embeddable": true,
                "href": "https:\/\/www.polive3d.com\/zh_cn\/wp-json\/wp\/v2\/tags?post=3516"
            }
        ],
        "curies": [
            {
                "name": "wp",
                "href": "https:\/\/api.w.org\/{rel}",
                "templated": true
            }
        ]
    }
}