Why PP Printing Needs Neither a Heated Bed nor an Enclosure
Because PP must release heat as it cools. We print PPpro open-frame at room temperature; a brim and PPLOCK26811 handle adhesion, not heat.
Our own PP printing uses no heated bed and no enclosure. We have printed many models on an open-frame Bambu Lab A1 with the bed at room temperature and the machine fully open, in a stable air-conditioned room. This is not a workaround for a difficult material; it follows from how PP actually cools.
PP needs to get rid of heat, not take more of it in
PP has to absorb and release a large amount of heat as it cools and crystallises. A heated bed keeps feeding heat in from below, and an enclosure traps that heat around the part. Both slow down the cooling the material is trying to complete. What PP wants is a stable, cool ambient that carries heat away evenly, which is why an air-conditioned room with the door and lid open lets parts set faster and more uniformly than a sealed, heated chamber.
Adhesion: a brim plus PPLOCK26811
Instead of using heat to hold the first layer down, we add a generous brim to enlarge the contact area and coat the build plate with PPLOCK26811 adhesive. Apply a thin, even layer, wait a few minutes until it dries, then print directly on top of it. One application lasts for multiple prints, and the plate cleans up with a wipe of alcohol. No heated bed, no PP tape, no special build surface.
Warping is solved in the design
Corner lift comes from stress concentration and uneven shrinkage, so we remove the causes in the model rather than adding hardware: replace right-angle corners with rounded fillets, add thickened mouse ears at the corners, enlarge the bottom contact area, and keep wall thickness as uniform as possible. Combined with a brim and PPLOCK26811, the part stays flat without any extra heat.
What this means in practice
On a desktop open-frame printer such as the Bambu Lab A1, the working recipe is simple: heated bed off, enclosure off, a stable air-conditioned room, a brim, one coat of PPLOCK26811, and a part designed with fillets and even walls. The usual PP checklist of a hot bed, a sealed chamber and PP tape tries to fight shrinkage by adding heat. Our experience goes the other way, and that is the whole point.
PP 打印真的需要加热床吗?
不需要。我们实操打印全程关闭加热床、用常温平台,在开放式的 Bambu Lab A1 上也打了很多模型。PP 冷却结晶时要吸收并释放大量热量,从下方继续补热并不能帮助定型,真正需要的是稳定、偏凉、能把热量均匀带走的环境。加热床不在我们的流程里。
为什么反而要开箱(开放机架)打印、不封箱?
封箱会把热量困在零件周围。PP 冷却时要散掉大量热量,闷着会拖慢结晶、反而影响尺寸稳定。在空调房里开门开盖、开放机架打印,散热更快更均匀——所以哪怕在桌面机上,我们也是全开放、不封箱、不加热床。
不用加热床,PP 怎么粘得住平台?
两样东西:裙边和 PPLOCK26811。先加宽裙边扩大首层接触面积,再在平台上薄薄均匀涂一层 PPLOCK26811 专用胶水,等几分钟干透,直接在上面打印即可。一次涂抹可支撑多次打印,不用每次重涂;要清洁时用酒精擦一下就行。不需要加热床、PP 胶带或专用平台。
不加热、不封箱,翘边怎么解决?
靠设计解决,不靠硬件。直角改圆角、角落加底部加厚的老鼠耳朵、增大底部接触面积、壁厚尽量均匀——这些手段消除了应力集中和收缩不均,翘边的根因就没了。再配合裙边和 PPLOCK26811,打印开始前翘边就已经被处理掉了。
入门开放式机器(比如 Bambu A1)真能打 PP 吗?
能。我们在 Bambu A1 上关掉加热床、全开放状态下打了很多模型。关键就几件事:稳定的空调房环境、均匀冷却、加裙边、涂一次 PPLOCK26811、把零件设计做对。不需要封闭式工业机,也不需要加热腔体。
PPLOCK26811 涂一次能用多久?平台怎么清洁?
一次涂抹可以多次打印。首次打印前等几分钟干透,之后直接往上打即可,每次之间不用重涂。想换新表面时用酒精擦一遍就行——不用刮、不用强溶剂、不用每次打印前补涂。
为什么常规 PP 打印那套做法在这里不适用?
常规建议(80–100°C 热床、密封封箱、PP 胶带)是给普通 PP 线材写的,思路是靠加热去对抗收缩。我们的实操相反:PP 结晶时需要把热量散出去,所以在稳定的空调房里开放机架、常温平台打印;粘附和翘边交给裙边、PPLOCK26811 和零件设计。把热量再加回去,是跟材料对着干,不是顺着它。
Related Reading
- What Is PPpro? A Modified PP 3D Printing Filament That Needs No Heated Bed and Makes Living Hinges
- Does PP printing need an enclosure? Open-frame printing test with POLIVE PPpro™
- Does PP Printing Need a Heat Bed? Room-Temperature Printing and Cooling Setup
- How to Prevent PP Warping? How to Choose Between Brim, Raft, and Skirt
- How to Design PP Parts for 3D Printing? Wall Thickness, Fillets, Snap Fits and Warp Prevention
- What Print Bed Should Be Used for PP 3D Printing? A Comparison of Common Bed Materials

