Why Does PP Printing Need Neither a Heated Bed nor an Enclosure?

Why PP Printing Needs Neither a Heated Bed nor an Enclosure

Because PP must release heat as it cools. We print PPpro open-frame at room temperature; a brim and PPLOCK26811 handle adhesion, not heat.

Our own PP printing uses no heated bed and no enclosure. We have printed many models on an open-frame Bambu Lab A1 with the bed at room temperature and the machine fully open, in a stable air-conditioned room. This is not a workaround for a difficult material; it follows from how PP actually cools.

PP needs to get rid of heat, not take more of it in

PP has to absorb and release a large amount of heat as it cools and crystallises. A heated bed keeps feeding heat in from below, and an enclosure traps that heat around the part. Both slow down the cooling the material is trying to complete. What PP wants is a stable, cool ambient that carries heat away evenly, which is why an air-conditioned room with the door and lid open lets parts set faster and more uniformly than a sealed, heated chamber.

Adhesion: a brim plus PPLOCK26811

Instead of using heat to hold the first layer down, we add a generous brim to enlarge the contact area and coat the build plate with PPLOCK26811 adhesive. Apply a thin, even layer, wait a few minutes until it dries, then print directly on top of it. One application lasts for multiple prints, and the plate cleans up with a wipe of alcohol. No heated bed, no PP tape, no special build surface.

Warping is solved in the design

Corner lift comes from stress concentration and uneven shrinkage, so we remove the causes in the model rather than adding hardware: replace right-angle corners with rounded fillets, add thickened mouse ears at the corners, enlarge the bottom contact area, and keep wall thickness as uniform as possible. Combined with a brim and PPLOCK26811, the part stays flat without any extra heat.

What this means in practice

On a desktop open-frame printer such as the Bambu Lab A1, the working recipe is simple: heated bed off, enclosure off, a stable air-conditioned room, a brim, one coat of PPLOCK26811, and a part designed with fillets and even walls. The usual PP checklist of a hot bed, a sealed chamber and PP tape tries to fight shrinkage by adding heat. Our experience goes the other way, and that is the whole point.

Does PP Printing Really Need a Heated Bed?

No. In our own printing we keep the heated bed off throughout and use a room-temperature build plate; we have printed many models on an open-frame Bambu Lab A1 as well. As PP cools and crystallises it has to absorb and release a large amount of heat. Continuing to add heat from below does not help it set — what it really needs is a stable, cool ambient that carries heat away evenly. A heated bed has no place in our workflow.

Why Go the Other Way: Print Open-Frame Rather Than in an Enclosure?

An enclosure traps heat around the part. PP has to shed a great deal of heat as it cools, and sealing it in slows crystallisation and ends up hurting dimensional stability. In an air-conditioned room, printing with the door and lid open on an open-frame machine dissipates heat faster and more evenly — so even on a desktop printer we run fully open, with no enclosure and no heated bed.

Without a Heated Bed, How Does PP Stick to the Build Plate?

Two things: a brim and PPLOCK26811. First add a generous brim to enlarge the first-layer contact area, then coat the build plate with a thin, even layer of PPLOCK26811 adhesive, wait a few minutes for it to dry, and print directly on top of it. One application lasts for multiple prints, with no need to recoat between them; to clean the plate, just wipe it with alcohol. No heated bed, no PP tape, no special build surface.

With No Heat and No Enclosure, How Is Warping Handled?

By design, not by hardware. Replacing right-angle corners with rounded fillets, adding thickened mouse ears at the corners, enlarging the bottom contact area and keeping wall thickness as uniform as possible remove the stress concentration and uneven shrinkage that cause corner lift in the first place. Combined with a brim and PPLOCK26811, warping is dealt with before printing even starts.

Can an Entry-Level Open-Frame Machine (Such as the Bambu A1) Really Print PP?

Yes. We have printed many models on a Bambu A1 with the heated bed off and the machine fully open. It comes down to a few things: a stable air-conditioned room, even cooling, a brim, one coat of PPLOCK26811, and getting the part design right. You do not need a sealed industrial machine or a heated chamber.

How Long Does One Coat of PPLOCK26811 Last, and How Do You Clean the Build Plate?

One coat supports multiple prints. Let it dry for a few minutes before the first print, then simply print onto it; there is no need to recoat between prints. To refresh the surface, just wipe it with alcohol — no scraping, no strong solvents, and no reapplication before every print.

Why Does the Conventional PP Printing Advice Not Apply Here?

The usual recommendations (an 80–100°C heated bed, a sealed enclosure, PP tape) were written for standard PP filament; the idea is to fight shrinkage by adding heat. Our experience is the opposite: as PP crystallises it needs to shed heat, so we print on an open-frame machine with a room-temperature plate in a stable air-conditioned room, and leave adhesion and warping to the brim, PPLOCK26811 and the part design. Putting heat back in works against the material, not with it.

Related Reading

Jack Lin

Leave a Comment