Are PP Prints Strong? How to Assess PP's Mechanical Properties

Are PP Prints Strong? How to Assess PP’s Mechanical Properties


Are PP printed parts strong?

Whether PP printed parts are “strong” cannot be answered with a single number.

If what you care about isrigidity, PP is usually not a particularly outstanding material; but if what you care about istoughness, impact resistance and repeated bending ability, PP often has the advantage.

Therefore, when judging the mechanical properties of PP printed parts, you need to consider the specific loading mode:

  • tension
  • bending
  • impact

and you also need to consider print orientation, wall thickness, infill density, print temperature and material formulation.


Strength is not a single number: tension, bending, impact

The “strength” in a material datasheet actually contains several different indicators.

Tensile performance

Tensile testing mainly observes how a material behaves when subjected to a pulling force, for example:

  • tensile strength
  • Elongation at break
  • elastic modulus

Tensile strength reflects the stress level a material can withstand during tension; elongation at break reflects how much deformation it can undergo before fracture.

For PP, high ductility and toughness are among its important characteristics.

Bending performance

Bending testing helps understand how a material behaves under bending loads.

In addition to bending strength, you can also look atbending modulus, which is the material’s ability to resist bending deformation.

For actual printed parts, bending performance is related to the part’s:

  • Wall thickness
  • geometry
  • Fill rate
  • Print orientation

are all related.

impact performance

Impact testing focuses on the material’s ability to resist failure under instantaneous loads.

For example:

  • drops
  • collision
  • instantaneous impact
  • rapid bending

A typical characteristic of PP is its good toughness, so in some impact and repeated-deformation scenarios it is less prone to sudden fracture than some more brittle materials.

Simply put, PP printed parts under load tend todeform to some extent before failing, rather than fracturing suddenly with no obvious deformation.

For POLIVE PPpro™, and the material formulation has been modified for PP 3D-printing applications, so its specific tensile, bending and other properties should be based on data under the corresponding test conditions.


Several key factors affecting the strength of PP printed parts

Even using the same PP filament, two printed parts can show significantly different mechanical behavior.

1. Print orientation

FDM printed parts are clearly anisotropic.

Because parts are formed layer by layer, there is a difference between material continuity in the XY plane and interlayer bonding in the Z direction.

Therefore, for the same test specimen, changing the print orientation can noticeably change the final tensile, bending and fracture behavior.

For load-bearing parts, the print orientation should be designed according to the actual load direction, rather than focusing only on the material’s own parameters.


2. Wall thickness and infill density

A part’s load-bearing capacity depends not only on the material but also on its structure.

For example:

  • Wall thickness
  • Number of wall lines
  • Fill rate
  • infill pattern
  • top and bottom layer thickness

all affect the final mechanical behavior of the part.

Therefore, you cannot simply assume that “because the material has high tensile strength, any part printed from it will be very strong.”

A thin-wall, high-infill part and a thick-wall, low-infill part may perform completely differently under actual load.


3. Print temperature and interlayer bonding

Print temperature affects the bonding between molten materials.

If the temperature or heat input is insufficient, the previous layer and the next layer may fail to fuse sufficiently, leading to poor interlayer bonding.

In this case, even if PP itself has good material toughness, the actual strength of the printed part may still be significantly affected.

Therefore, print temperature affects not only surface quality but also actual structural performance.


4. Material formulation

The properties of different PP formulations are not exactly the same.

Material modification can target:

  • rigidity
  • toughness
  • flowability
  • Interlayer bonding
  • Shrinkage behavior

and other aspects for adjustment.

For POLIVE PPpro™, and the specific mechanical properties should be based on actual test data and test conditions.

If engineering material selection is needed, it is recommended to also check:

  • tensile strength
  • Elongation at break
  • bending modulus
  • impact performance
  • Testing Standards
  • test direction
  • Testing Conditions

rather than looking only at a single “strength” number.


How does PP compare with PLA, PETG and ABS?

Different materials have different advantages, so it is more appropriate to compare them from specific applications.

PP vs PLA

PLA usually has higher rigidity and is more suitable for parts that need a harder surface.

PP’s advantages are more reflected in:

  • toughness
  • flexibility
  • Repeated bending
  • low density
  • chemical resistance

Therefore, if a part needs some flexibility or repeated motion, PP may be more suitable.


PP vs PETG

PETG usually achieves a relatively balanced trade-off among rigidity, toughness and printing convenience.

PP stands out more in:

  • low density
  • flexibility
  • Chemical resistance
  • repeated bending ability

The final choice depends on the part’s actual use environment and mechanical requirements.


PP vs ABS

ABS usually has good rigidity and a solid engineering foundation, while PP leans more toward lightweight, flexible and chemically resistant applications.

Therefore, PP is more suitable for some:

  • Snaps
  • Living hinge
  • containers
  • lightweight structural parts
  • parts that need repeated bending

while for structures requiring high rigidity such as load-bearing beams and supports, you need to judge based on specific design and test results.


How to verify the PP printed part in your hands?

If you need to know how much force a particular PP printed part can actually withstand, the most reliable method is not to simply refer to the material’s advertised parameters, but to performtests related to the actual part and printing process.

tensile testing

You can use standard or self-made dumbbell-shaped test specimens.

When testing, record:

  • Material grade
  • Print orientation
  • Nozzle temperature
  • Floor height
  • Fill rate
  • Number of wall lines
  • specimen dimensions

This makes test results easier to compare across different batches.

three-point bending

Three-point bending testing helps judge the ability of the material and printed part to resist bending deformation.

If your actual product mainly bears bending loads, this type of test is usually more meaningful than simply looking at tensile data.

impact testing

If the product may experience drops, collisions or instantaneous impacts, you can further perform impact testing.

For example, choose the appropriate pendulum impact, drop-weight or other verification method based on the actual application.


Why must print parameters be recorded during testing?

Test results for 3D-printing materials are closely related to printing conditions.

Even with the same filament, if you change:

  • Print orientation
  • Temperature
  • Floor height
  • Print speed
  • Fill rate
  • Wall thickness
  • Cooling conditions

the final test results may all change.

In addition, whether the specimen has been dried, annealed or otherwise post-processed may also affect the test results.

Therefore, a complete test report should not just write “tensile strength XX MPa”, but should also statethe test standard and sample preparation conditions.

For POLIVE PPpro™, if it is to be used for specific engineering selection, the actual data under the corresponding batch, test standard and test conditions should be used as the basis.


What loading scenarios are PP printed parts actually suitable for?

The key to understanding the mechanical properties of PP is not simply judging “whether PP is strong”, but judging:

whether it suits your loading mode.

If the part needs:

  • Repeated bending
  • some flexibility
  • Impact resistance
  • low weight
  • tolerance of chemical environments

PP may have a clear advantage.

If the part mainly requires:

  • high rigidity
  • very small deformation
  • high dimensional stability

then other materials need to be compared further, combined with specific structure testing.

The final mechanical performance comes from:

material + print parameters + print orientation + part structure

rather than the material name itself.


Summary

  • PP’s rigidity is usually not outstanding, but its toughness and impact resistance are its important characteristics.
  • Judging PP’s strength cannot rely on a single number; tensile, bending and impact performance should be considered separately.
  • Print orientation will significantly affect the actual mechanical properties of FDM parts.
  • Wall thickness, number of wall lines, infill density and structural design all affect the final load-bearing capacity.
  • Print temperature and interlayer bonding quality also affect the actual strength.
  • The mechanical properties of different PP formulations differ, and modified materials should be based on specific test data.
  • For actual load-bearing parts, it is recommended to first make test specimens, then verify according to the real working conditions.
  • When material selection is needed, you should check the test standard, sample preparation conditions and specific test data together, rather than comparing only a single strength number.

Is PP a High-Strength Material for Printed Parts?

Strength is not a single number — it has to be split into tensile, flexural and impact performance. PP leans towards toughness and impact resistance; stiffness is not its strong suit. So "is it strong" only means something once you say which kind of loading you mean.

What Affects the Strength of PP Parts the Most?

Print orientation, wall thickness and infill, and the interlayer bonding produced by nozzle temperature often matter more than the material grade. Always record your parameters during testing, otherwise the results cannot be reproduced.

How Do You Check Whether a PP Part Is Good Enough?

Test the assembled part under real conditions: actual load, actual direction, repeated loading and drop tests — not just pulling a standard test coupon. Rounded transitions and uniform wall thickness often improve performance faster than switching materials.

Which Loading Scenarios Suit PP?

Repeated bending, snap-fits, drop impacts and functional parts that need to absorb energy by deforming. For structural parts under long-term constant high load, or requiring high rigidity and very stable dimensions, choose a different material.

Related Reading

  • What is Modified PP? What Exactly Does POLIVE PPpro™ Change?
  • How Strong Are the Interlayer Bonds of PP Prints? How to Improve Z-Direction Strength
  • Are PP 3D-printed parts drop-resistant? A comparison of impact resistance: PP vs. PETG and ABS
  • Can PP Make Living Hinges? Printing One-Piece Living Hinges with POLIVE PPpro™

Jack Lin

Leave a Comment